{"product_id":"se-electronics-x1-a-large-diaphragm-condenser-microphone","title":"sE Electronics X1 A Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe sE Electronics X1 A is a wired cardioid condenser microphone for studio recording, podcasting, vocals, instruments, and close-miked sources. It connects through a standard 3-pin XLR output and is designed for use with microphone preamps or audio interfaces that provide 48 V phantom power. Its focused cardioid pickup pattern helps prioritize the sound in front of the microphone while reducing pickup from the rear.\u003c\/p\u003e\u003cp\u003eBuilt for creators who need one microphone for varied sessions, the X1 A is suited to vocals, acoustic instruments, guitar cabinets, drums, brass, piano, and room recording. Its frequency range extends from 20 Hz to 20 kHz, with a balanced response intended for detailed capture. The microphone's 20 mV\/Pa sensitivity supports practical use with typical recording interfaces and console preamps.\u003c\/p\u003e\u003cp\u003eA switchable -20 dB attenuation pad expands the X1 A's usable range for high-volume sources and close-miking. With the pad disengaged, it handles up to 130 dB SPL; with the pad engaged, maximum SPL handling reaches 150 dB SPL at 0.5% THD and 1 kHz. This makes it suitable for louder applications such as amplified guitar, brass, and drum recording when paired with an appropriate preamp gain setting.\u003c\/p\u003e\u003cp\u003eThe X1 A also includes a switchable 100 Hz low-cut filter with a 6 dB-per-octave slope. This filter can help reduce rumble, footfall noise, and excess low-frequency buildup from close placement. Used alongside careful microphone positioning, it gives recording setups a straightforward way to manage unwanted low end before the signal reaches the recording chain.\u003c\/p\u003e\u003cp\u003eIts 2\/3-inch back-electret condenser capsule is housed in a durable all-metal chassis with an integrated windscreen and a gold-plated XLR connector. The internal windscreen helps reduce wind noise and plosive effects while protecting the capsule. The X1 A can serve as a primary entry-level studio microphone or as a flexible additional microphone in a growing recording setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the source in front of the microphone and reduces rear pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e2\/3-Inch Condenser Capsule:\u003c\/strong\u003e Captures vocals and instruments with a broad 20 Hz to 20 kHz frequency range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable -20 dB Pad:\u003c\/strong\u003e Supports close-miking and louder sources by reducing the incoming signal level.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e100 Hz Low-Cut Filter:\u003c\/strong\u003e Helps manage rumble, footfall noise, and excess proximity-effect bass.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e150 dB Maximum SPL:\u003c\/strong\u003e Handles high sound-pressure sources when the attenuation pad is engaged.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll-Metal Housing:\u003c\/strong\u003e Provides durable physical protection and helps reject electrical interference.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe X1 A uses an all-metal body, an integrated windscreen, and a gold-plated 3-pin male XLR connector. It measures 58 mm in diameter and 169 mm long, with a microphone weight of 390 g. The package includes a swivel microphone clip and a microphone-stand thread adapter for physical mounting.\u003c\/p\u003e\u003cp\u003eMount the microphone on a stable stand using the included clip and adapter, then connect its XLR output to a compatible microphone preamp, mixer, or audio interface. Enable 48 V phantom power only through equipment intended to supply P48 power, and begin with conservative preamp gain. For loud instruments or close placement, engage the -20 dB pad; use the 100 Hz low-cut filter when low-frequency noise or buildup needs reduction.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669492883526,"sku":"X1 A","price":91.78,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61YvTnJ9KaL.jpg?v=1784508332","url":"https:\/\/audiowatt.store\/products\/se-electronics-x1-a-large-diaphragm-condenser-microphone","provider":"Audio Watt Store","version":"1.0","type":"link"}