{"title":"Podcast \u0026 Streaming Picks","description":null,"products":[{"product_id":"rode-broadcaster-broadcast-condenser-microphone","title":"RØDE BROADCASTER Broadcast Condenser Microphone","description":"\u003cp\u003eThe RØDE BROADCASTER is a large-diaphragm condenser microphone made for broadcast speech, voice-over work, podcasting, and studio narration. Its end-address design helps presenters maintain a natural speaking position while recording directly into the microphone head. It is intended for systems where clear vocal capture and professional XLR connectivity are needed.\u003c\/p\u003e\u003cp\u003eA cardioid pickup pattern focuses on the speaker in front of the microphone while reducing pickup from the rear. The voice-tailored response and emphasized proximity effect can add perceived warmth and low-frequency weight when used close to the source. This makes it well suited to close-miked spoken-word applications.\u003c\/p\u003e\u003cp\u003eThe BROADCASTER uses a 1-inch HF2 capsule with a gold-plated diaphragm and JFET-based active electronics. Its 20 Hz to 20 kHz frequency range, 14 dB SPL equivalent noise rating, and 128 dB SPL maximum rating support detailed voice recording with useful headroom. An internal pop filter helps reduce plosive sounds before they reach the capsule.\u003c\/p\u003e\u003cp\u003eA switchable 75 Hz high-pass filter helps reduce low-frequency rumble from HVAC systems, traffic, vibration, and other environmental sources. The microphone also has an On-Air indicator LED for studio workflows. With the supplied 5-pin connector installed and wired to a compatible console, the LED can be controlled through switch contacts.\u003c\/p\u003e\u003cp\u003eThe BROADCASTER connects to a microphone preamp, mixer, audio interface, or broadcast console through XLR and requires phantom power. It can operate from 24V or 48V phantom power, although RØDE's operating guidance specifies a 48V phantom supply for normal use. The included stand mount, zip pouch, and On-Air indicator adaptor support studio installation and storage.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLarge 1-Inch Capsule:\u003c\/strong\u003e Supports detailed vocal capture for broadcast and voice-over work.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pattern:\u003c\/strong\u003e Prioritizes sound from the front of the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Pop Filter:\u003c\/strong\u003e Helps reduce plosive noise during close speech recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e75 Hz High-Pass Filter:\u003c\/strong\u003e Reduces low-frequency rumble and vibration when engaged.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOn-Air LED:\u003c\/strong\u003e Provides a visible live-microphone status indicator.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhantom-Powered XLR Output:\u003c\/strong\u003e Integrates with compatible professional audio equipment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe BROADCASTER has a rugged stainless-steel body and a large-diaphragm, end-address condenser design. Its HF2 capsule uses a gold-plated diaphragm, while the active circuitry uses a JFET impedance converter with a bipolar output buffer. The microphone weighs 577 g and measures 167 mm long, 50 mm high, and 65 mm deep.\u003c\/p\u003e\u003cp\u003eMount the microphone lengthwise in the included RM2 stand mount and speak directly into the head. Connect it with an XLR microphone cable to equipment that supplies phantom power, then allow a brief stabilization period after power is applied. Use the rear high-pass filter switch when low-frequency noise is present; installation of the supplied 5-pin connector for console-controlled On-Air LED operation is best handled by an experienced audio or electronics technician.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668847059014,"sku":"BROADCASTER","price":405.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/518doUmIdyL.jpg?v=1784467158"},{"product_id":"rode-interviewgopur-purple-wireless-handheld-microphone-adaptor","title":"RØDE INTERVIEWGOPUR Purple Wireless Handheld Microphone Adaptor","description":"\u003cp\u003eThe RØDE INTERVIEWGOPUR Interview GO is a purple handheld adaptor designed to turn a compatible RØDE wireless transmitter into a handheld interview microphone. It gives compact clip-on transmitters a more familiar reporter-style format for person-to-person interviews and presentations. The adaptor is intended for users who want to bring the microphone closer to a speaker without changing their wireless recording setup.\u003c\/p\u003e\u003cp\u003eThis accessory is well suited to field reporters, content creators, event hosts, and mobile production teams. Its handle provides an ergonomic grip for passing the microphone between interviewer and guest. The purple finish also makes it easy to identify within a multi-microphone kit.\u003c\/p\u003e\u003cp\u003eThe Interview GO works with the transmitter's built-in microphone, so its sound character depends on the compatible wireless system installed in the adaptor. A removable windshield fits over the transmitter area to help reduce plosives and wind noise. This makes the setup more practical for spoken-word recording in interviews, presentations, and on-location content.\u003c\/p\u003e\u003cp\u003eRØDE builds the Interview GO around a simple transmitter cradle and handle design rather than adding electronics, batteries, or audio controls. The transmitter slides into the top mount, while the windshield covers the microphone area. This preserves the wireless operation and routing of the paired RØDE system.\u003c\/p\u003e\u003cp\u003eUse the Interview GO as an accessory within a RØDE Wireless GO, Wireless GO II, Wireless GO (Gen 3), Wireless ME, or Wireless PRO system. It is a useful upgrade path when a clip-on transmitter needs the handling and visual presence of a handheld microphone. A compatible wireless transmitter and its receiver or recording device are required separately.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHandheld Conversion:\u003c\/strong\u003e Changes a compatible RØDE wireless transmitter into a handheld microphone format.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSeries IV Compatibility:\u003c\/strong\u003e Supports current RØDE Series IV wireless transmitters for flexible system use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemovable Windshield:\u003c\/strong\u003e Helps reduce plosives and wind noise around the transmitter microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eErgonomic Handle:\u003c\/strong\u003e Provides a comfortable, familiar grip for interviews and presentations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePurple Finish:\u003c\/strong\u003e Adds clear visual identification to a wireless microphone setup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePassive Accessory Design:\u003c\/strong\u003e Requires no battery, charging, wiring, or separate audio settings.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe Interview GO combines a slim handheld adaptor with a removable popshield-style windshield. The adaptor measures 237 mm tall and weighs 84 g, while the windshield weighs 8 g. Its compact dimensions make it easy to carry alongside a compatible RØDE wireless microphone system.\u003c\/p\u003e\u003cp\u003eTo set up, place a compatible transmitter into the top transmitter mount and fit the windshield over the transmitter area. Use it for handheld interviews, field reporting, presentations, or mobile content creation where the transmitter needs to function as a pass-around microphone. The adaptor does not include a wireless transmitter, receiver, or recording device.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668848107590,"sku":"INTERVIEWGOPUR","price":29.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61F-7zpOP1L.jpg?v=1784467366"},{"product_id":"rode-m2-live-performance-condenser-vocal-microphone","title":"RØDE M2 Live Performance Condenser Vocal Microphone","description":"\u003cp\u003eThe RØDE M2 is a handheld condenser microphone built for live vocal performance. It provides a detailed, full-range vocal capture for singers, presenters, and performers using a PA system or professional audio mixer. Its focused pickup pattern helps keep the intended voice prominent in busy stage environments.\u003c\/p\u003e\u003cp\u003eDesigned for stage use, the M2 combines condenser-microphone detail with a tight supercardioid polar pattern. This pattern helps reduce spill from nearby instruments and stage monitors while supporting feedback-conscious microphone placement. It is well suited to live singing, spoken-word work, and presentations where vocal clarity matters.\u003c\/p\u003e\u003cp\u003eA 0.5-inch internally shock-mounted condenser capsule is at the center of the M2's design. The microphone covers a 35Hz to 20kHz frequency range and handles sound-pressure levels up to 141dB SPL. Its JFET impedance converter and bipolar output buffer support balanced operation with compatible professional audio equipment.\u003c\/p\u003e\u003cp\u003eThe M2 uses a rugged all-metal body intended for repeated live use. A built-in on\/off switch can be locked with its screw mechanism to help prevent accidental switching during a performance. The microphone also offers high RF rejection and low handling noise for practical stage operation.\u003c\/p\u003e\u003cp\u003eFor use in a system, connect the M2 to a balanced XLR microphone input that supplies 24V or 48V phantom power. It can be used with mixing consoles, PA systems, audio interfaces, and other compatible XLR-equipped equipment. An included mic clip and padded zip pouch help support transport and stand-mounted use.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCondenser Vocal Capsule:\u003c\/strong\u003e Captures detailed vocal sound for live performances and presentations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the performer and reduces surrounding spill.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternally Shock-Mounted Capsule:\u003c\/strong\u003e Helps reduce noise caused by handling and movement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLockable On\/Off Switch:\u003c\/strong\u003e Helps prevent unintended switching during live use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll-Metal Body:\u003c\/strong\u003e Provides a durable housing for regular stage handling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24V\/48V Phantom Power:\u003c\/strong\u003e Works with compatible mixers and interfaces providing phantom power.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe M2 has a black, heavy-duty all-metal body with an end-address design and a 47mm diameter. Its 0.5-inch condenser capsule is internally shock-mounted, while the integrated switch includes a locking screw. The microphone weighs 308g and measures 187mm long.\u003c\/p\u003e\u003cp\u003eConnect the M2 using a standard balanced 3-pin XLR microphone cable to an input that provides P24 or P48 phantom power. Use the included RM3 mic clip for stand mounting, and aim the front of the microphone toward the vocalist while positioning monitors outside the supercardioid pickup area. The included padded zip pouch is useful for storage and transport.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668850892870,"sku":"M2-RODE","price":170.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/610SN1aEVvL.jpg?v=1784467738"},{"product_id":"rode-nt6-compact-condenser-microphone-with-remote-capsule","title":"Rode NT6 Compact Condenser Microphone with Remote Capsule","description":"\u003cp\u003eThe Rode NT6 is a compact small-diaphragm condenser microphone designed for close, discreet, and difficult-to-reach microphone placement. Its remote capsule separates the recording head from the preamp body, helping users position the capsule where a conventional microphone body may not fit. It is suited to instrument recording, location work, broadcast, theatre, live performance, and environmental recording.\u003c\/p\u003e\u003cp\u003eA fixed cardioid pickup pattern focuses capture toward the intended source while reducing pickup from the sides and rear. The NT6 covers a 40Hz to 20kHz frequency range and uses a 1\/2-inch externally biased, gold-sputtered condenser capsule. Its compact capsule supports detailed close-miking without placing a full microphone body directly at the recording position.\u003c\/p\u003e\u003cp\u003eThe capsule connects to the remote preamp body with a 3m shielded, Kevlar-reinforced cable. This split design allows the capsule to remain in a tight or visually unobtrusive location while the preamp controls stay accessible elsewhere. A multi-position mounting ring provides 180 degrees of vertical capsule adjustment for accurate aiming.\u003c\/p\u003e\u003cp\u003eThe preamp body includes a selectable 80Hz high-pass filter and a -10dB pad. The high-pass filter can help reduce low-frequency rumble and vibration when those frequencies are not part of the desired source. The pad adds headroom for louder instruments and sound sources, raising maximum SPL handling to 145dB with the pad enabled.\u003c\/p\u003e\u003cp\u003eThe NT6 uses a balanced 3-pin XLR output and requires 24V or 48V phantom power from a compatible mixer, audio interface, recorder, or microphone preamp. Its RM5 stand mount, WS5 windshield, and padded pouch support practical studio and field deployment. It can serve as a compact standalone microphone or as a focused component within a larger recording setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemote 1\/2-Inch Capsule:\u003c\/strong\u003e Places the recording head in tight or discreet locations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the intended sound source.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e3m Kevlar-Reinforced Cable:\u003c\/strong\u003e Separates the capsule from the remote preamp body.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e80Hz High-Pass Filter:\u003c\/strong\u003e Helps reduce unwanted low-frequency rumble and vibration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e-10dB Pad:\u003c\/strong\u003e Adds headroom when recording louder sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24V Or 48V Phantom Power:\u003c\/strong\u003e Works with compatible professional microphone inputs.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT6 uses an externally biased, gold-sputtered condenser capsule and a heavy-duty satin-nickel plated preamp body. Its surface-mount preamp circuitry is housed separately from the capsule, while the included capsule mounting ring provides two-axis adjustment and 180 degrees of vertical rotation. The capsule assembly supports 1\/4-inch mounting and includes adapters for common microphone stand, tripod, and boompole thread sizes.\u003c\/p\u003e\u003cp\u003eMount the capsule close to the desired source using the swivel mount, then route the supplied 3m cable to the preamp body and secure the body with the included RM5 stand mount as needed. Connect a standard balanced XLR microphone cable from the preamp body to a mixer, recorder, or interface that provides 24V or 48V phantom power. Set the high-pass filter or pad before recording, and ensure miniature cable connectors are aligned correctly before inserting them.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668879597638,"sku":"NT6","price":449.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81imxC74YkL.jpg?v=1784468677"},{"product_id":"rode-ntk-large-diaphragm-tube-condenser-microphone","title":"RØDE NTK Large-Diaphragm Tube Condenser Microphone","description":"\u003cp\u003eThe RØDE NTK is a large-diaphragm valve condenser microphone for studio recording applications that call for detailed capture and a controlled cardioid pickup pattern. It is designed for recording sources such as vocals, acoustic instruments, piano, guitar amplifiers, and drum overheads. Its dedicated external power supply supports the tube-based microphone circuitry.\u003c\/p\u003e\u003cp\u003eA 1-inch gold-sputtered condenser capsule and hand-selected 6922 twin-triode valve are at the center of the NTK design. This combination is intended to deliver a warm, full recording character while retaining detail across its 20Hz to 20kHz frequency range. The fixed cardioid pattern helps focus pickup toward the intended source while reducing sound arriving from behind the microphone.\u003c\/p\u003e\u003cp\u003eThe NTK is suited to creators, musicians, engineers, and studios building an XLR-based recording chain. Its 25mV\/Pa sensitivity and low 12dBA equivalent noise level support capture of nuanced vocal and instrument performances. With a maximum SPL rating above 158dB, it can also accommodate high-level sound sources when positioned and gain-staged appropriately.\u003c\/p\u003e\u003cp\u003eClass-A valve circuitry uses a valve\/tube impedance converter with a bipolar output buffer. The microphone connects to its dedicated power supply through a 7-pin cable, while the power supply feeds a mixer or microphone preamplifier through XLR. This separates the microphone from mains power hardware and provides a practical interface for conventional studio equipment.\u003c\/p\u003e\u003cp\u003eThe NTK can serve as a primary vocal microphone or as a character-focused option alongside other studio condensers. Its included external power supply integrates with a mixer, preamp, or audio interface that accepts an XLR microphone signal. For vocal work, a pop filter and stable stand setup help manage plosives, moisture, and placement consistency.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Gold-Sputtered Capsule:\u003c\/strong\u003e Provides a large-diaphragm condenser platform for detailed recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6922 Twin-Triode Valve:\u003c\/strong\u003e Uses a hand-selected tube in the microphone circuit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the front of the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e Rated at 12dBA equivalent noise for quieter sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Handles sound-pressure levels above 158dB SPL.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDedicated Power Supply:\u003c\/strong\u003e Powers the valve circuitry and provides XLR output.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NTK uses a side-address body with a high-strength, heat-treated steel mesh head. Its internal design combines a pressure-gradient condenser capsule, Class-A valve circuitry, and a hand-selected 6922 tube. The microphone measures 208 x 55 x 55mm and has a net weight of 760g.\u003c\/p\u003e\u003cp\u003eConnect the microphone to the dedicated power supply with the supplied 7-pin microphone cable before connecting the power supply to mains power. Run an XLR microphone cable from the power supply output to a mixer, preamplifier, or audio interface, and secure the microphone on a stable stand using the supplied mount or shock mount. Position the gold dot toward the source, and use a pop filter for vocal recording; do not disconnect the microphone cable while the system is powered.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668881694790,"sku":"NTK","price":619.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/6108nO_65IL.jpg?v=1784468999"},{"product_id":"rode-wigogen3-wireless-go-gen-3-microphone-system","title":"RØDE WIGOGEN3 Wireless GO (Gen 3) Microphone System","description":"\u003cp\u003eThe RØDE Wireless GO (Gen 3) is a compact dual-channel wireless microphone system designed for creators who need clear, flexible audio without a large production setup. It includes two transmitters and one receiver, making it well suited to interviews, presentations, vlogs, mobile video and two-person recordings. Its compact format helps keep microphones close to the speaker while keeping cables and accessories to a minimum.\u003c\/p\u003e\u003cp\u003eThis system is made for use with cameras, smartphones, tablets and computers through its analog and digital connections. The receiver can connect to a camera through its 3.5mm output or to compatible mobile devices and computers through USB-C. Each transmitter can use its built-in microphone or accept an external locking 3.5mm TRS lavalier microphone.\u003c\/p\u003e\u003cp\u003eRØDE Series IV 2.4 GHz digital transmission carries audio from the transmitters to the receiver with 128-bit encryption. The system offers a stated line-of-sight range of up to 260 meters, giving creators useful flexibility for moving subjects and wider camera positions. Its omnidirectional built-in microphones are designed to capture speech naturally from a clipped-on position.\u003c\/p\u003e\u003cp\u003eEach transmitter includes 32 GB of internal memory for 32-bit float onboard recording. This creates an independent recording option that can be used as a primary track or as a backup to the receiver output. The format provides wide recording headroom for post-production recovery of recordings that were captured too loudly or quietly.\u003c\/p\u003e\u003cp\u003eGainAssist, adjustable output gain and routing options help adapt the Wireless GO to different recording workflows. Merged mode can combine sources for a simple stereo output, while Split mode keeps the two transmitters on separate channels for editing. The included charging hub, cables, windshields and carry pouch make this a complete starting point for portable wireless recording.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-Channel System:\u003c\/strong\u003e Records two wireless microphone sources with one receiver.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSeries IV Wireless:\u003c\/strong\u003e Uses encrypted 2.4 GHz digital transmission up to 260 meters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e32-Bit Float Recording:\u003c\/strong\u003e Creates onboard backup recordings with broad post-production headroom.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGainAssist Control:\u003c\/strong\u003e Helps manage microphone levels during changing recording conditions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlexible Device Connectivity:\u003c\/strong\u003e Connects to cameras, phones and computers via included cables.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSafety Channel Mode:\u003c\/strong\u003e Records a second output channel at a lower level.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe Wireless GO (Gen 3) uses compact clip-on transmitter and receiver units with integrated rechargeable lithium-ion batteries. Each transmitter has a built-in omnidirectional microphone, a locking 3.5mm TRS input, USB-C connectivity and dedicated status indicators. The receiver adds a bright LCD display, navigation controls, a routing-mode selector, USB-C connectivity and a 3.5mm TRRS output for monitoring or analog device connection.\u003c\/p\u003e\u003cp\u003eFor a camera setup, clip a transmitter to the speaker, connect the receiver to the camera with the included 3.5mm TRS cable, and set the camera input level appropriately. For compatible phones, tablets and computers, connect the receiver by USB-C using the included USB-C or Lightning cable as appropriate. Use the included furry windshields outdoors, enable onboard recording when a backup track is desired, and configure advanced settings through RØDE Central.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668893720646,"sku":"WIGOGEN3","price":142.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61feWshwtsL.jpg?v=1784469942"},{"product_id":"rode-wimicrocblu-usb-c-wireless-microphone-system-blue","title":"RØDE WIMICROCBLU USB-C Wireless Microphone System, Blue","description":"\u003cp\u003eThe RØDE Wireless Micro WIMICROCBLU is a compact two-person wireless microphone system designed for recording directly to USB-C smartphones. Its plug-in receiver eliminates the need for an audio cable between the phone and receiver, helping keep mobile video rigs simple and uncluttered. Two clip-on transmitters with built-in microphones let creators capture dialogue from two people at once.\u003c\/p\u003e\u003cp\u003eThis system suits smartphone videographers, social-media creators, interviewers, presenters, and anyone who needs clearer voice capture than a phone microphone can typically provide. The transmitters pair automatically with the receiver for a straightforward setup process. They can be clipped to clothing or used with the included magnetic attachments for flexible placement.\u003c\/p\u003e\u003cp\u003eEach transmitter uses an omnidirectional built-in microphone with a 20 Hz to 20 kHz frequency range and a maximum SPL rating of 135 dB. RØDE's GainAssist technology automatically manages recording levels to help maintain balanced audio across changing voice levels. The built-in acoustic chamber is designed to reduce the effect of wind noise and plosives on spoken-word recordings.\u003c\/p\u003e\u003cp\u003eThe Wireless Micro provides more than 100 meters of transmission range and operates for up to 7 hours per transmitter charge. Its charging case supplies two additional transmitter charges, for up to 21 hours of total operating time. Included furry windshields provide additional wind-noise reduction for outdoor recording.\u003c\/p\u003e\u003cp\u003eFor a mobile content workflow, the USB-C receiver connects directly to a compatible smartphone and works with apps that accept USB audio. The receiver can also be used as a class-compliant USB audio interface with computers for stereo or dual-mono recording. Users wanting to add camera connectivity can use the separately available Wireless Micro Camera Receiver or Wireless Micro Camera Kit.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUSB-C Smartphone Receiver:\u003c\/strong\u003e Connects directly to a compatible USB-C phone without a receiver cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo Built-In Microphones:\u003c\/strong\u003e Records two speakers with compact clip-on transmitters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGainAssist Level Control:\u003c\/strong\u003e Automatically manages audio levels for more consistent recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOmnidirectional Pickup:\u003c\/strong\u003e Captures natural voice sound as subjects move or turn.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCharging Case:\u003c\/strong\u003e Provides two additional transmitter charges for extended use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMagnetic And Clip Mounting:\u003c\/strong\u003e Gives flexible, low-profile placement on clothing.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe blue Wireless Micro system uses ultra-compact transmitters with integrated clothing clips, separate magnetic attachments, and a pocket-sized charging case. Each transmitter weighs 12 g without its magnet or 18 g with it, while the USB-C receiver weighs 6 g. The transmitters include an acoustic chamber around their built-in microphones and feature a splashproof design for mobile recording use.\u003c\/p\u003e\u003cp\u003eFor setup, charge the case with the included USB-C to USB-C cable, remove the transmitters from the case, and plug the USB-C receiver into a compatible phone. Clip each transmitter near the speaker's mouth, avoiding heavy obstruction from clothing or hair; use the included furry windshields in windier outdoor conditions. The receiver works with recording apps that accept USB audio, while RØDE Central and RØDE Capture provide access to supported settings and firmware updates.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668930224198,"sku":"WIMICROCBLU","price":92.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61e49TlHd2L.jpg?v=1784470631"},{"product_id":"shure-blx14-cvl-h11-wireless-lavalier-system","title":"Shure BLX14\/CVL-H11 Wireless Lavalier System","description":"\u003cp\u003eThe Shure BLX14\/CVL-H11 is a complete wireless lavalier system for presenters, instructors, clergy, and other spoken-word users who need hands-free mobility. It combines the BLX4 single-channel receiver, BLX1 bodypack transmitter, and CVL cardioid lavalier microphone in one coordinated package. The H11 version operates in the 572–596 MHz frequency band, so local spectrum authorization should be verified before use.\u003c\/p\u003e\u003cp\u003eThe CVL clip-on microphone offers a compact, discreet way to capture speech without requiring the user to hold a microphone. Its cardioid pickup pattern is designed to focus on sound arriving from the front while reducing some surrounding sound. This makes the system well suited to classrooms, conference rooms, houses of worship, and presentation spaces.\u003c\/p\u003e\u003cp\u003eBLX wireless technology provides a working range of up to 300 feet line of sight, although actual range depends on RF interference, reflections, and obstructions. The BLX1 bodypack uses two AA batteries and can operate for up to 14 hours with alkaline batteries. A front-panel battery indicator helps the user monitor transmitter status during an event.\u003c\/p\u003e\u003cp\u003eThe BLX4 receiver supports one-touch group scanning to locate an available group and channel, then the bodypack can be matched to the selected setting. Its front-panel LEDs show received audio status and transmitter readiness, while the display shows the active group and channel. The receiver provides both balanced XLR microphone-level output and unbalanced 1\/4-inch instrument-level output for connection to a mixer or amplifier.\u003c\/p\u003e\u003cp\u003eFor installations with more than one wireless system, BLX supports up to 12 simultaneous systems when the band and RF environment allow it. The H11 system can serve as a straightforward single-speaker solution or as part of a coordinated multi-system setup. Keeping the receiver in line of sight, away from metal surfaces and nearby interference sources, helps support dependable operation.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eH11 UHF Band:\u003c\/strong\u003e Operates from 572–596 MHz; confirm local authorization before use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Presenter System:\u003c\/strong\u003e Includes a BLX4 receiver, BLX1 bodypack, and CVL lavalier microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Lavalier Mic:\u003c\/strong\u003e Focuses pickup toward the speaker for clear spoken-word use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp To 300-Foot Range:\u003c\/strong\u003e Supports mobile presentations with line-of-sight operation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp To 14-Hour Battery Life:\u003c\/strong\u003e BLX1 runs on two AA alkaline batteries.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne-Touch Channel Scan:\u003c\/strong\u003e Receiver scans for an available group and channel.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe BLX1 bodypack and BLX4 receiver use molded ABS housings designed for portable professional audio use. The bodypack has a belt clip, integrated antenna, TA4 microphone input, group\/channel display, and adjustable audio gain. The CVL microphone uses a TA4F connector, includes a lavalier clip and windscreen, and has a 1.3 m cable.\u003c\/p\u003e\u003cp\u003eConnect the BLX4 receiver to its PS24 power supply, then connect its XLR or 1\/4-inch output to a compatible mixer or amplifier. Perform a receiver group scan, set the BLX1 to the matching group and channel, and adjust bodypack gain while watching the receiver audio LED. For best results, place the receiver with a clear line of sight to the transmitter and position the lavalier to avoid contact with clothing or jewelry.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668941758534,"sku":"BLX14\/CVL-H11","price":342.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51oVTactKjL.jpg?v=1784471940"},{"product_id":"shure-blx14-sm31-j11-wireless-fitness-headset-system","title":"Shure BLX14\/SM31-J11 Wireless Fitness Headset System","description":"\u003cp\u003eThe Shure BLX14\/SM31-J11 is a wireless fitness headset system built for instructors, trainers, presenters, and active speakers who need hands-free voice reinforcement. It combines a BLX4 single-channel tabletop receiver, BLX1 bodypack transmitter, and SM31FH headworn condenser microphone. The system gives users a practical way to move freely while sending microphone audio to a compatible mixer, powered speaker, or PA system.\u003c\/p\u003e\u003cp\u003eThe SM31FH headset uses a cardioid pickup pattern and a vocal-focused frequency response to help reproduce speech with clarity. Its flexible gooseneck allows the capsule to be positioned close to the speaker's mouth, while the included windscreen helps reduce breath, wind, and plosive noise. This makes the system especially suitable for fitness instruction and other high-movement voice applications.\u003c\/p\u003e\u003cp\u003eThe BLX wireless platform uses analog UHF transmission and provides up to 300 feet of line-of-sight operating range under suitable conditions. The J11 version is designated for the 596–616 MHz frequency range in current Shure BLX documentation. Actual range and available frequencies depend on local RF conditions, interference, and regional spectrum authorization.\u003c\/p\u003e\u003cp\u003eFor long classes, rehearsals, and events, the BLX1 bodypack runs on two AA alkaline batteries for up to 14 hours. Its adjustable gain control allows the user to set an appropriate level for the connected headset microphone. Receiver audio and ready indicators provide quick visual confirmation of signal and operating status.\u003c\/p\u003e\u003cp\u003eThe BLX4 receiver provides both balanced XLR microphone-level output and 1\/4-inch instrument-level output for connection to sound systems. Its group and channel controls support scanning for an available operating channel during setup. As a complete single-channel package, the BLX14\/SM31-J11 is a straightforward wireless voice solution for an existing PA, mixer, or powered-speaker system.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Wireless System:\u003c\/strong\u003e Includes the BLX4 receiver, BLX1 bodypack, and SM31FH headset microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJ11 UHF Band:\u003c\/strong\u003e Uses the J11 frequency band listed as 596–616 MHz in current Shure documentation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitness-Ready Headset:\u003c\/strong\u003e Hydrophobic microphone construction helps resist moisture-related corrosion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Microphone:\u003c\/strong\u003e Focused pickup pattern supports clear voice capture in active environments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp To 14-Hour Runtime:\u003c\/strong\u003e BLX1 bodypack operates on two AA alkaline batteries.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFlexible Audio Outputs:\u003c\/strong\u003e BLX4 receiver offers XLR and 1\/4-inch audio connections.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe BLX1 transmitter and BLX4 receiver use molded ABS housings designed for regular portable use. The SM31FH has a lightweight wireframe headset design, flexible gooseneck, TA4F connector, and moisture-repellent microphone cartridge housing. A clothing clip and windscreen are included with the system.\u003c\/p\u003e\u003cp\u003eConnect the BLX4 receiver to its supplied external power supply, then connect its XLR or 1\/4-inch output to a compatible mixer, amplifier, powered speaker, or PA input. Install the included AA batteries in the BLX1, connect the SM31FH headset, and match the transmitter group and channel to the receiver after performing a receiver scan. Position the headset capsule near the corner of the mouth and adjust bodypack gain while monitoring the receiver audio LED.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668942708806,"sku":"BLX14\/SM31-J11","price":429.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51b6wzYkMiL_cf170db5-664b-4f72-a2c5-7f6fae949046.jpg?v=1784472147"},{"product_id":"shure-se21dybk-tw2-aonic-215-gen-2-wireless-earbuds","title":"Shure SE21DYBK+TW2 AONIC 215 Gen 2 Wireless Earbuds","description":"\u003cp\u003eThe Shure AONIC 215 Gen 2 is a true wireless Sound Isolating earphone system built around Shure's detachable SE215 earphones and RMCE-TW2 secure-fit adapters. It provides a cable-free listening option for music, calls, commuting, exercise, and everyday mobile use. The over-ear design helps keep the earphones stable while the included sleeve selection supports a personalized in-ear seal.\u003c\/p\u003e\u003cp\u003eIts single dynamic MicroDriver design is tuned for clear sound with deep bass, while passive Sound Isolating technology can reduce outside noise by up to 37 dB. This approach helps listeners hear detail without relying on active noise cancellation. Environment Mode can be enabled when awareness of nearby sound is needed.\u003c\/p\u003e\u003cp\u003eBluetooth 5 connectivity supports Qualcomm aptX, AAC, and SBC codecs for use with compatible phones, tablets, laptops, and other Bluetooth audio sources. The system has a stated wireless range of up to 10 m (30 ft). Integrated beamforming microphones support stereo phone and video calls.\u003c\/p\u003e\u003cp\u003eEach charge provides up to 8 hours of playback, and the included charging case supplies three additional full charges for up to 32 hours total. Physical button controls provide access to playback, calls, volume, and Environment Mode functions. The earphones also power on automatically when removed from the charging case.\u003c\/p\u003e\u003cp\u003eThe modular MMCX connection makes this set useful for listeners who want to move between true wireless and compatible wired Shure accessories. The included AONIC 215 earphones can be detached from the wireless adapters and connected to other compatible MMCX cable options. ShurePlus PLAY app support adds EQ, button-control, firmware, and Environment Mode adjustments.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSingle Dynamic MicroDriver:\u003c\/strong\u003e Delivers clear sound with deep bass from the included SE215 earphones.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSound Isolating Design:\u003c\/strong\u003e Passive isolation blocks up to 37 dB of outside noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSecure Over-Ear Fit:\u003c\/strong\u003e Low-profile routing helps keep the earphones in place during activity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e32-Hour Battery System:\u003c\/strong\u003e Up to 8 hours per charge plus three case recharges.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBluetooth 5 Audio:\u003c\/strong\u003e Supports aptX, AAC, and SBC codecs with a 10 m range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEnvironment Mode:\u003c\/strong\u003e Lets outside sound in when situational awareness is needed.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe black AONIC 215 Gen 2 uses detachable MMCX earphones and left\/right secure-fit wireless adapters. Soft Flex and foam sleeves in small, medium, and large sizes are included to help create a secure seal. The earphones and adapters are IPX4 rated for sweat and water resistance, although the charging case is not water resistant.\u003c\/p\u003e\u003cp\u003eNo vehicle installation or wiring is required. Charge the case with the included USB-C charging cable, remove the earphones to enter pairing mode, and select “SHURE AONIC TW2” from a compatible Bluetooth device. For wired listening, detach the earphones from the adapters and use a separately available compatible Shure MMCX cable accessory.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668991795270,"sku":"SE21DYBK+TW2","price":299.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61q4q4frr_L.jpg?v=1784475813"},{"product_id":"shure-se425-cl-professional-sound-isolating-earphones","title":"Shure SE425-CL Professional Sound Isolating Earphones","description":"\u003cp\u003eThe Shure SE425-CL Professional Sound Isolating Earphones are wired in-ear monitors designed for detailed listening, personal monitoring, and everyday playback. Their sound-isolating fit helps reduce surrounding noise so listeners can focus on program material without relying solely on higher volume. They are a practical choice for musicians, engineers, commuters, and listeners who prefer a secure wired connection.\u003c\/p\u003e\u003cp\u003eDual balanced-armature drivers provide the SE425 with accurate, natural sound across a specified 20 Hz to 19 kHz frequency range. The design is intended to present detail clearly for music playback and onstage monitoring. With 109 dB SPL\/mW sensitivity and 22-ohm impedance at 1 kHz, the earphones are suited to compatible portable and professional headphone outputs.\u003c\/p\u003e\u003cp\u003eThe low-profile earpieces route the cable over the ear to help keep the earphones stable and keep cable movement out of the way. A proper seal is important to both isolation and bass response, so Shure includes several sleeve styles and sizes. This lets each user choose a fit based on comfort, retention, and the level of isolation needed.\u003c\/p\u003e\u003cp\u003eA detachable 64-inch clear cable uses gold-plated MMCX connectors with a lock-snap fit and 360-degree rotation. The cable can be replaced if it is damaged or swapped for a compatible Shure accessory cable. Its 3.5 mm stereo mini plug connects directly to many headphone outputs, while the included threaded adapter supports 6.35 mm connections.\u003c\/p\u003e\u003cp\u003eThe SE425-CL can serve as a focused listening upgrade for a portable player, headphone amplifier, audio interface, or compatible in-ear monitoring receiver. It does not require an external amplifier for basic use, but source equipment must provide a compatible 3.5 mm headphone output or an appropriate adapter. A premium carrying case is supplied for storage and transport.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual Balanced-Armature Drivers:\u003c\/strong\u003e Separate drivers deliver detailed, accurate sound reproduction.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSound Isolating Fit:\u003c\/strong\u003e Included sleeves can block up to 37 dB of outside noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOver-Ear Cable Routing:\u003c\/strong\u003e Helps keep the earphones secure during movement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDetachable MMCX Cable:\u003c\/strong\u003e Enables cable replacement without replacing the earphones.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e360-Degree Connector Rotation:\u003c\/strong\u003e Helps tailor cable position for a comfortable fit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eProfessional Connection Options:\u003c\/strong\u003e Includes 3.5 mm and 6.35 mm headphone connectivity.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe SE425-CL uses a discreet in-ear form factor with clear components, an over-ear wireform cable arrangement, and detachable gold-plated MMCX connectors. The connector system has a lock-snap fit and allows rotation at the earpiece for positioning comfort. The supplied premium carrying case helps protect the earphones and accessories between uses.\u003c\/p\u003e\u003cp\u003eChoose the sleeve that creates a comfortable, secure seal, then route the cable over the ears and use the cable cinch to manage slack if needed. Connect the 3.5 mm plug to a compatible headphone jack, or attach the supplied 6.35 mm threaded adapter for compatible professional equipment. For best low-frequency performance and isolation, reseat the earphones or try another sleeve size if the seal feels loose.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668995629126,"sku":"SE425-CL","price":299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/6102EoNE3xL.jpg?v=1784475900"},{"product_id":"fender-quantum-lt-4-usb-c-audio-interface","title":"Fender Quantum LT 4 USB-C Audio Interface","description":"\u003cp\u003eThe Fender Quantum LT 4 is a compact 4-in, 2-out USB-C audio interface for musicians, podcasters, streamers, and home-studio creators who need flexible recording connections. It combines microphone, line-level, and instrument recording options in one desktop-friendly unit. Its layout is especially useful for recording a vocal-and-guitar performance, a duo, or multiple sources at once.\u003c\/p\u003e\u003cp\u003eTwo MAX-HD microphone preamps provide up to 75 dB of gain for detailed capture with a wide range of microphones. Fender specifies a transparent, low-noise signal path designed to preserve the natural character of vocals and acoustic instruments. Two dedicated Hi-Z instrument inputs are also optimized for direct recording from electric guitar, bass, and other instruments.\u003c\/p\u003e\u003cp\u003eThe Quantum LT 4 supports 24-bit audio at sample rates up to 192 kHz, with custom low-latency drivers for responsive computer-based recording. This helps performers monitor and track in real time with a streamlined workflow. Balanced main outputs and a headphone output support practical monitoring with studio speakers and headphones.\u003c\/p\u003e\u003cp\u003eLoopback audio lets creators combine computer audio with live microphone or instrument sources for streaming, podcasting, and content production. Standalone Mixer Mode allows the interface to be used for simple analog-style mixing without a computer or DAW. Direct-monitoring control can also be managed through Fender Studio Pro or Universal Control.\u003c\/p\u003e\u003cp\u003eFor guitar-focused production, registered hardware unlocks the Fender Amp \u0026amp; FX Pack in the Fender Studio app. The interface also includes a six-month Fender Studio Pro demo, giving new users a starting point for recording and production. Its USB-C connection, compact dimensions, and flexible input arrangement make it a practical foundation for a growing desktop recording setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e4x2 USB-C Interface:\u003c\/strong\u003e Provides four inputs and two output channels for compact multi-source recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual MAX-HD Preamps:\u003c\/strong\u003e Supplies up to 75 dB of gain for microphones requiring substantial clean gain.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual Instrument Inputs:\u003c\/strong\u003e Connect guitars, basses, and other high-impedance instruments directly to the interface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24-Bit\/192 kHz Audio:\u003c\/strong\u003e Supports high-resolution recording across common professional sample rates.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLoopback Audio:\u003c\/strong\u003e Combines system audio and live inputs for streaming, podcasting, and content creation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandalone Mixer Mode:\u003c\/strong\u003e Enables simple computer-free analog-style mixing when a DAW is not needed.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe Quantum LT 4 has a compact black desktop form factor measuring 7 inches wide, 3.5 inches deep, and 1.75 inches high. Its connection layout includes combo microphone\/line inputs, front-facing Hi-Z instrument inputs, balanced 1\/4-inch TRS main outputs, and a 1\/4-inch TRS headphone output. At 1.8 pounds, it is suited to permanent desktop setups as well as portable recording rigs.\u003c\/p\u003e\u003cp\u003eConnect the interface to a compatible computer through USB-C, then connect microphones, line-level equipment, instruments, headphones, and powered monitors as needed. Use the balanced TRS outputs with compatible studio monitors and the front instrument inputs for direct guitar or bass tracking. Fender Studio Pro or Universal Control can be used to manage direct-monitoring functions, while Mixer Mode supports simple operation without a computer.\u003c\/p\u003e","brand":"Fender","offers":[{"title":"Default Title","offer_id":45669188829254,"sku":"QUANTUM LT4","price":169.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81WQGaxyzKL.jpg?v=1784480687"},{"product_id":"presonus-studio-24c-2x2-usb-c-audio-interface","title":"PreSonus Studio 24c 2x2 USB-C Audio Interface","description":"\u003cp\u003eThe PreSonus Studio 24c is a compact 2x2 USB-C audio and MIDI interface for recording microphones, instruments, and line-level sources to a computer. It provides two combination mic\/instrument\/line inputs and two balanced main outputs for a straightforward desktop recording setup. It is suited to musicians, podcasters, producers, and mobile creators who need a small interface with dedicated monitor and headphone control.\u003c\/p\u003e\u003cp\u003eTwo XMAX-L solid-state microphone preamps provide the front end for vocal, acoustic, and spoken-word recording. Each input has its own gain control, while the combination jacks accept XLR microphones or 1\/4-inch instrument and line connections. Global +48V phantom power supports compatible condenser microphones.\u003c\/p\u003e\u003cp\u003eThe Studio 24c records at up to 24-bit\/192 kHz and supports common sample rates from 44.1 through 192 kHz. Its converter dynamic range is specified at 108 dB, helping preserve detail when tracking and playing back audio. Four ladder-style LED meters provide visual monitoring for the two inputs and main left\/right output channels.\u003c\/p\u003e\u003cp\u003eA front-panel Mixer control blends direct input sound with computer playback for latency-free input monitoring. This is useful when recording vocals, guitar, bass, or narration while listening to an existing session. Separate Main and headphone level controls make it practical to manage powered monitors and headphones from the interface itself.\u003c\/p\u003e\u003cp\u003eFor system integration, the Studio 24c provides balanced 1\/4-inch TRS main outputs, a stereo headphone output, and 5-pin MIDI input and output. It is USB bus powered and connects to computers through USB-C, with USB-C-to-C and USB-C-to-A cables included. The listed package includes Studio One 6 Artist Edition recording software, giving a compatible starting point for recording and production.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e2x2 Simultaneous I\/O:\u003c\/strong\u003e Record two sources and monitor in stereo.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eXMAX-L Preamps:\u003c\/strong\u003e Connect microphones, instruments, or line-level equipment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24-Bit\/192 kHz Audio:\u003c\/strong\u003e Supports detailed recording at high sample rates.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDirect Monitoring Mixer:\u003c\/strong\u003e Blend inputs and computer playback without monitoring delay.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced Main Outputs:\u003c\/strong\u003e Connect powered studio monitors using 1\/4-inch TRS cables.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMIDI I\/O:\u003c\/strong\u003e Integrate compatible keyboards, controllers, and MIDI hardware.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe Studio 24c uses a compact, road-rugged all-metal chassis with metal control knobs for desktop or mobile recording use. Its front panel places the combo inputs, gain controls, monitoring controls, and level meters within easy reach. The rear panel groups the main outputs, headphone output, MIDI ports, and USB-C connection for organized routing.\u003c\/p\u003e\u003cp\u003eConnect the interface directly to a computer with the included USB-C-to-C or USB-C-to-A cable; it is compatible with USB 2.0 and USB 3.0 connections, but not USB 1.1. Use XLR cables for microphones, 1\/4-inch cables for instruments or line sources, and balanced 1\/4-inch TRS cables for powered monitors. The headphone output mirrors the main left\/right playback streams, while the Mixer knob is the preferred control for setting a direct-monitoring balance during recording.\u003c\/p\u003e","brand":"PreSonus","offers":[{"title":"Default Title","offer_id":45669201838150,"sku":"STUDIO24C","price":149.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71uy0deWZ0L.jpg?v=1784481475"},{"product_id":"arturia-audiofuse-16rig-usb-audio-interface","title":"Arturia AudioFuse 16Rig USB Audio Interface","description":"\u003cp\u003eThe Arturia AudioFuse 16Rig is a multi-channel USB-C audio interface designed to centralize a hardware-based studio, recording rig, or advanced monitoring setup. It provides 16 analog line inputs, dedicated microphone and instrument connectivity, digital expansion, MIDI routing, and multiple analog outputs in a single 1U-capable unit. This makes it suited to producers and musicians who need to keep synthesizers, effects, monitors, and computer-based recording connected at the same time.\u003c\/p\u003e\u003cp\u003eTwo digitally controlled microphone preamps support microphones, line-level sources, and Hi-Z instruments on the front-panel combo inputs. The interface also provides access to inputs 3 and 4 through a front-panel 3.5 mm stereo input for convenient connection of a portable source. With 24-bit\/192 kHz conversion and published low-distortion, wide-dynamic-range specifications, it is intended for detailed recording and monitoring across varied source types.\u003c\/p\u003e\u003cp\u003eAudioFuse 16Rig is built for flexible signal flow rather than a fixed, simple desktop-interface layout. Its eight DC-coupled line outputs can serve external processors, alternate monitor paths, reamping tasks, or compatible CV-oriented hardware, while dedicated speaker outputs support primary monitoring. A second speaker pair can be configured using a pair of line outputs for A\/B monitor comparison.\u003c\/p\u003e\u003cp\u003eFor larger systems, dual ADAT input and output ports provide optical digital expansion, while word clock I\/O supports synchronization with compatible digital equipment. MIDI connectivity includes one DIN input and two DIN output\/thru ports, plus a USB MIDI host connection for compatible class-compliant USB MIDI devices. The integrated USB hub connections help reduce connection clutter around a computer-centered setup.\u003c\/p\u003e\u003cp\u003eTwo internal low-latency mixers allow the interface to operate without a computer connection for selected routing and mixing applications. Front-panel controls, a color display, and AudioFuse Control Center software provide access to configuration, metering, monitoring, and routing functions. It can sit on a desktop or be installed in a 1U rack, making it a practical hub for studios that may expand over time.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e16 Analog Inputs:\u003c\/strong\u003e Connect numerous line-level instruments and hardware sources simultaneously.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo Combo Preamps:\u003c\/strong\u003e Record microphones, instruments, or line-level sources from the front panel.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDC-Coupled Outputs:\u003c\/strong\u003e Route audio or compatible control-voltage signals to external hardware.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual ADAT I\/O:\u003c\/strong\u003e Add digital channels through compatible optical expansion equipment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStandalone Mixers:\u003c\/strong\u003e Manage selected mixing and routing tasks without a computer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMIDI And Word Clock:\u003c\/strong\u003e Integrate MIDI hardware and synchronize compatible digital devices.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eAudioFuse 16Rig uses a robust metal chassis in a single-space rack form factor, with rack ears that can be rotated for rackmount or tabletop use. Its front panel combines a color display, rotary controls, monitoring controls, combo inputs, headphone connections, and accessible USB MIDI hosting. The rear panel concentrates the high-density analog, digital, synchronization, MIDI, USB, and power connections for organized system wiring.\u003c\/p\u003e\u003cp\u003eConnect the supplied external power supply and use the USB-C port to connect the interface to a compatible computer when computer audio operation is needed. Use balanced TRS cabling for line inputs, line outputs, and speaker outputs where appropriate; ADAT optical cables and 75-ohm BNC cables are required for compatible digital expansion and word-clock systems. For standalone operation, configure routing and mixer settings from the front panel or AudioFuse Control Center before disconnecting the computer.\u003c\/p\u003e","brand":"Arturia","offers":[{"title":"Default Title","offer_id":45669350572102,"sku":"AUDIOFUSE 16Rig","price":1299.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61OsVzsnfzL.jpg?v=1784493584"},{"product_id":"se-electronics-dynacaster-dcm-8-dynamic-microphone","title":"sE Electronics DYNACASTER DCM 8 Dynamic Microphone","description":"\u003cp\u003eThe sE Electronics DYNACASTER DCM 8 is a front-addressed cardioid dynamic microphone designed for broadcast-style voice capture, podcasting, livestreaming, recording, and instrument use. Its XLR-based design suits creators and musicians who use an audio interface, mixer, or microphone preamp rather than a USB microphone. The focused cardioid pickup pattern helps prioritize the source in front of the microphone while reducing pickup from the rear.\u003c\/p\u003e\u003cp\u003eFor voice work, the DCM 8 is built to provide a close, controlled presentation with onboard tools for adjusting the microphone's tonal starting point. Two recessed acoustic trim switches provide six available EQ configurations for tailoring low- and high-frequency character before software or console processing. This gives users practical adjustment options without requiring an external inline EQ for basic voicing changes.\u003c\/p\u003e\u003cp\u003eThe microphone includes sE's switchable DYNAMITE preamp, which provides an additional 30 dB of gain when engaged. The active mode requires 48V phantom power and is useful with interfaces or preamps that do not provide ample gain for a typical dynamic microphone. With the preamp switched off, the DCM 8 can be used as a conventional passive dynamic microphone.\u003c\/p\u003e\u003cp\u003eA DMC8 dynamic capsule with an aluminum voice coil and neodymium magnet supports a stated 20 Hz to 19 kHz frequency range. The microphone is front-addressed, making it well suited to boom-arm and desk-mounted setups where the speaker addresses the end of the mic. Its integrated capsule shock-absorption system is designed to reduce the need for a separate external shockmount.\u003c\/p\u003e\u003cp\u003eThe DCM 8 combines several useful recording accessories into its body, including an internal three-layer pop filter and an integrated stand mount with a wide swivel range. The internal pop filter is removable for cleaning, while an external windscreen is also supplied for users who prefer additional wind protection. Its all-metal housing, XLR output, included thread adapter, and boom-arm compatibility make it a practical fit for podcast, streaming, studio, vocal, and instrument-recording systems.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable DYNAMITE Preamp:\u003c\/strong\u003e Adds 30 dB of gain when powered by 48V phantom power.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Dynamic Capsule:\u003c\/strong\u003e Focuses on the source in front of the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSix EQ Configurations:\u003c\/strong\u003e Recessed acoustic trim switches tailor low and high frequencies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated Shock Absorption:\u003c\/strong\u003e Helps reduce vibration and handling-related mechanical noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Layer Pop Filter:\u003c\/strong\u003e Helps control plosives without an external pop filter.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFront-Addressed XLR Design:\u003c\/strong\u003e Works with interfaces, mixers, stands, and broadcast boom arms.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe DCM 8 uses an all-metal housing with a matte black finish, a gold-plated 3-pin male XLR connector, and a black external windscreen. Its front-addressed body incorporates the capsule shock-absorption system, internal pop filter, recessed control switches, and stand mount into one microphone assembly. The rear-mounted controls are recessed to help protect settings during transport and regular use.\u003c\/p\u003e\u003cp\u003eConnect the microphone to an audio interface, mixer, or microphone preamp using a balanced XLR-to-XLR microphone cable. Enable 48V phantom power only when using the DYNAMITE preamp; the active preamp mode draws 3.0 mA and requires phantom power delivered through XLR connections. Mount the microphone on a compatible stand or broadcast boom arm using its integrated mount and supplied thread adapter, then position the front of the microphone toward the speaker or sound source.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669430820934,"sku":"DYNACASTER DCM 8","price":286.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81pvDs1FtHL.jpg?v=1784502219"},{"product_id":"se-electronics-se7sf-sidefire-condenser-microphone","title":"sE Electronics sE7sF SideFire Condenser Microphone","description":"\u003cp\u003eThe sE Electronics sE7sF sE7 sideFire is a small-diaphragm condenser microphone with a 90-degree side-address capsule. It is designed for close-miking instruments where conventional end-address pencil microphones can be difficult to position. The sideways capsule orientation helps fit the microphone into compact drum, piano, guitar, and acoustic-instrument setups.\u003c\/p\u003e\u003cp\u003eThis cardioid microphone is suited to studio recording and live sound applications requiring focused pickup and practical placement flexibility. Its 1\/2-inch back-electret condenser capsule is engineered for a natural, balanced response across its 20 Hz to 20 kHz operating range. The ultra-thin diaphragm supports quick transient response for detailed percussion, strings, acoustic guitar, and cymbal capture.\u003c\/p\u003e\u003cp\u003eThe sE7 sideFire uses discrete Class-A electronics and a transformerless output design. This combination supports a clear signal path with a specified equivalent noise level of 16 dB(A). With 19 mV\/Pa sensitivity and a 78 dB signal-to-noise ratio, it is built for detailed instrument recording with standard microphone preamps and audio interfaces.\u003c\/p\u003e\u003cp\u003eA switchable 20 dB pad expands the microphone's use on high-volume sound sources. Maximum SPL handling is rated at 136 dB without the pad and 156 dB with the pad engaged, both measured at 0.5% THD. A switchable 80 Hz low-cut filter helps reduce footfall noise, rumble, wind noise, and excess bass from close placement.\u003c\/p\u003e\u003cp\u003eThe sE7sF connects through a gold-plated 3-pin male XLR output and requires 48 V phantom power. Its compact all-metal body is appropriate for regular studio and stage use, while the included mic clip, thread adapter, and windscreen help get it mounted quickly. It can be used as a single close microphone or paired with another sE7 sideFire for stereo and ambient recording applications.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e90-Degree SideFire Capsule:\u003c\/strong\u003e Side-address pickup simplifies placement in confined instrument setups.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the source while reducing off-axis sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable 20 dB Pad:\u003c\/strong\u003e Accommodates louder instruments and close-miking positions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e80 Hz Low-Cut Filter:\u003c\/strong\u003e Reduces rumble, footfall noise, and close-miking bass buildup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTransformerless Class-A Circuitry:\u003c\/strong\u003e Supports a short, clean signal path.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e48 V Phantom Operation:\u003c\/strong\u003e Works with compatible microphone preamps, mixers, and interfaces.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE7 sideFire has an all-metal chassis with a high-quality finish and a gold-plated 3-pin male XLR connector. Its body measures 23 mm in diameter and 130 mm long, with a weight of 163 g. The capsule is rotated 90 degrees from the microphone body for side-address positioning in tight or unconventional locations.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a balanced XLR microphone input that supplies 48 V phantom power according to IEC 61938. Use the included mic clip and thread adapter to mount it on a standard microphone stand, then aim the side-address capsule toward the sound source. Engage the 20 dB pad for high-SPL sources and use the 80 Hz low-cut filter when rumble, wind noise, or excessive proximity-effect bass is present.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669451432006,"sku":"sE7sF","price":129.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61U9pYnkVHL.jpg?v=1784504243"},{"product_id":"se-electronics-v7-ve-vintage-dynamic-vocal-microphone","title":"sE Electronics V7 VE Vintage Dynamic Vocal Microphone","description":"\u003cp\u003eThe sE Electronics V7 VE is a wired handheld dynamic microphone designed for vocals, speech, broadcasting, podcasting, and instrument recording. Its supercardioid pickup pattern helps focus on the intended source while reducing pickup from surrounding stage sound. The Vintage Edition pairs the V7 platform with a green hammered finish and polished chrome grille.\u003c\/p\u003e\u003cp\u003eThis microphone is suited to singers, presenters, content creators, engineers, and performers who need an XLR microphone for live or studio use. Its dynamic capsule is built around an aluminum voice coil and neodymium magnet. The 40 Hz to 19 kHz frequency range supports vocal detail while retaining useful low-frequency reach.\u003c\/p\u003e\u003cp\u003eThe V7 VE uses a supercardioid polar pattern for strong off-axis rejection and increased gain before feedback in monitored live-sound setups. This makes it a practical choice for loud stages, rehearsals, spoken-word systems, and close-miked recording. The pattern also calls for thoughtful monitor placement, since supercardioid microphones have rear pickup lobes.\u003c\/p\u003e\u003cp\u003eA patented integrated shockmount decouples the capsule from mechanical vibration to help reduce handling noise. An internal windscreen helps control wind noise and plosive sounds during close vocal use. The gold-plated 3-pin male XLR connection provides a standard balanced analog output for compatible microphone inputs.\u003c\/p\u003e\u003cp\u003eThe V7 VE can connect to a mixer, PA system, microphone preamp, audio interface, or recorder using a standard XLR microphone cable. It includes a mic clip and thread adapter for stand mounting, plus a carrying pouch for transport. It can also be used on electric guitar cabinets and drums where its dynamic design and directional pickup suit the application.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Pickup:\u003c\/strong\u003e Focuses on the source and helps reduce surrounding stage bleed.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAluminum Voice Coil:\u003c\/strong\u003e Forms part of the dynamic DMC7 capsule design.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated Shockmount:\u003c\/strong\u003e Helps isolate the capsule from handling vibration and rumble.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Windscreen:\u003c\/strong\u003e Helps reduce plosives and unwanted wind noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll-Metal Construction:\u003c\/strong\u003e Uses a zinc-alloy chassis and spring-steel grille.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGold-Plated XLR:\u003c\/strong\u003e Provides a durable 3-pin balanced audio connection.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe Vintage Edition has an all-metal body with a green hammered finish and polished chrome grille. Its chassis is made from zinc alloy, while the spring-steel mesh grille is corrosion-resistant and designed to resist dents. A beveled grille edge helps keep the microphone from rolling when placed on a flat surface.\u003c\/p\u003e\u003cp\u003eConnect the V7 VE to a mixer, audio interface, recorder, or PA system with a standard XLR microphone cable; a suitable microphone input and preamp are required. Mount it in the included mic clip on a compatible stand using the supplied thread adapter when needed. For live use, place stage monitors away from the microphone's rear pickup area and aim the microphone toward the performer.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669478367302,"sku":"V7 VE","price":119.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81sQ0qELQYS.jpg?v=1784506958"},{"product_id":"se-electronics-v7-white-supercardioid-dynamic-vocal-microphone","title":"sE Electronics V7 WHITE Supercardioid Dynamic Vocal Microphone","description":"\u003cp\u003eThe sE Electronics V7 WHITE is a wired handheld dynamic microphone designed for vocals, speech, broadcasting, podcasting, and close-miked instruments. Its supercardioid pickup pattern helps focus on the intended source while reducing pickup from surrounding stage sound. It connects through a standard 3-pin male XLR output.\u003c\/p\u003e\u003cp\u003eThis microphone is suited to performers, presenters, content creators, and engineers who need a durable handheld mic with a focused directional pattern. The V7 WHITE uses a dynamic DMC7 capsule, so it does not require external power to operate. Its frequency range extends from 40 Hz to 19 kHz.\u003c\/p\u003e\u003cp\u003eThe V7 WHITE is voiced around a specialized aluminum voice coil and neodymium magnet assembly. This combination is designed to provide a clear, open sound character while retaining the practical durability associated with a dynamic handheld microphone. Its 2.0 mV\/Pa sensitivity and 300-ohm electrical impedance make it appropriate for common XLR microphone inputs.\u003c\/p\u003e\u003cp\u003eA patented integrated shockmount decouples the capsule from mechanical vibration to reduce handling noise. The internal windscreen helps reduce wind noise and plosive sounds, and the included spare white windscreen can be installed for an all-white appearance. These details make the microphone useful for active stage performance as well as spoken-word recording.\u003c\/p\u003e\u003cp\u003eThe V7 WHITE can be used directly with a mixer, audio interface, microphone preamp, or PA system that provides an XLR microphone input. It is supplied with a microphone clip, thread adapter, spare white internal windscreen, and carrying pouch. Its white finish offers a visual alternative to the standard V7 while retaining the same core microphone format.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Pickup Pattern:\u003c\/strong\u003e Helps isolate the intended voice or instrument from nearby sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDynamic DMC7 Capsule:\u003c\/strong\u003e Provides a handheld dynamic microphone format without requiring external power.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAluminum Voice Coil:\u003c\/strong\u003e Supports the V7 WHITE's clear and open sound character.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated Shockmount:\u003c\/strong\u003e Reduces mechanical vibration transferred to the capsule during handling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Internal Windscreen:\u003c\/strong\u003e Helps reduce wind noise and plosive sounds while allowing a color change.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGold-Plated XLR Connector:\u003c\/strong\u003e Provides a durable 3-pin XLR signal connection.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe V7 WHITE has an all-metal design with a zinc-alloy chassis, white finish, and spring-steel mesh grille. Its beveled grille edge is intended to help prevent the microphone from rolling when set down. The grille is designed to resist dents and corrosion.\u003c\/p\u003e\u003cp\u003eConnect the microphone's 3-pin male XLR connector to a compatible XLR microphone cable, then connect that cable to a mixer, interface, preamp, or PA input. Use the included mic clip and thread adapter to mount it on a suitable microphone stand, or use it as a handheld microphone. The supplied carrying pouch is useful for transport and storage.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669478432838,"sku":"V7 WHITE","price":99.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61Ef2B6oeaL.jpg?v=1784506993"},{"product_id":"se-electronics-v7mc2gomp3-gold-wireless-mic-capsule","title":"sE Electronics V7MC2GOMP3 Gold Wireless Mic Capsule","description":"\u003cp\u003eThe sE Electronics V7MC2GOMP3 is a gold-finish dynamic wireless microphone capsule designed for compatible Sennheiser handheld transmitters. It lets performers change the vocal capsule on an existing wireless handheld rather than replacing the complete wireless system. This package includes the V7 MC2 Gold capsule, an MP03 protective pouch, and a thread cover.\u003c\/p\u003e\u003cp\u003eDesigned for vocals and speech, the V7 MC2 uses a supercardioid pickup pattern to focus on the intended performer while reducing pickup from surrounding sound sources. Its 40 Hz to 19 kHz frequency range and aluminum voice coil are engineered for a clear, detailed vocal presentation. The 300-ohm capsule is intended for live sound applications using a compatible Sennheiser wireless handheld transmitter.\u003c\/p\u003e\u003cp\u003eThe DMC7 dynamic capsule uses a neodymium magnet and specialized aluminum voice coil. Its supercardioid pattern helps provide useful isolation in stage environments where monitors, instruments, and other microphones may be nearby. This makes it a practical choice for singers, presenters, houses of worship, and production teams using compatible wireless systems.\u003c\/p\u003e\u003cp\u003eA patented integrated shockmount decouples the capsule from mechanical vibration to help reduce handling noise. The internal windscreen helps reduce wind noise and plosive sounds, and the Gold version includes a spare yellow internal windscreen for visual customization. Gold-plated contacts support a reliable connection between the capsule and compatible transmitter body.\u003c\/p\u003e\u003cp\u003eThe V7 MC2 Gold is an upgrade component, not a complete wireless microphone system. A compatible Sennheiser handheld transmitter and its associated receiver are required for operation. It is suited to users who want to tailor the vocal capsule and appearance of an existing wireless handheld setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSennheiser Compatibility:\u003c\/strong\u003e Designed for compatible Sennheiser wireless handheld transmitter bodies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Pattern:\u003c\/strong\u003e Focuses pickup on the performer and helps reduce surrounding sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDynamic DMC7 Capsule:\u003c\/strong\u003e Uses an aluminum voice coil and neodymium magnet.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated Shockmount:\u003c\/strong\u003e Helps reduce handling noise from movement and vibration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGold-Plated Contacts:\u003c\/strong\u003e Provide a dependable capsule-to-transmitter signal connection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMP03 Protection Set:\u003c\/strong\u003e Includes a protective pouch and thread cover for transport.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe V7 MC2 Gold uses an all-metal construction with a durable zinc-alloy chassis and a beveled spring-steel grille. The grille edge is shaped to help keep the handheld microphone from rolling when set down. Its gold finish is paired with a black internal windscreen, while a yellow spare internal screen is included.\u003c\/p\u003e\u003cp\u003eInstallation requires a compatible Sennheiser handheld wireless transmitter; this capsule does not operate by itself and does not include a transmitter or receiver. Remove the existing compatible capsule according to the transmitter manufacturer's instructions, then install the V7 MC2 securely before use. Confirm transmitter compatibility before purchase and use the included pouch and thread cover when transporting or storing the capsule.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669481480262,"sku":"V7MC2GOMP3","price":139.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/91UJHg5Fu1L.jpg?v=1784507745"},{"product_id":"se-electronics-x1-s-studio-bundle-condenser-mic-kit","title":"sE Electronics X1 S STUDIO BUNDLE Condenser Mic Kit","description":"\u003cp\u003eThe sE Electronics X1 S Studio Bundle is a complete recording package centered on the X1 S large-diaphragm cardioid condenser microphone. It is designed for creators who need a practical vocal, instrument, podcast, or voice-over setup without assembling each accessory separately. The included RF-X Reflexion Filter, shock mount, metal pop filter, and XLR cable help address common recording challenges such as room reflections, vibration, and vocal plosives.\u003c\/p\u003e\u003cp\u003eAt the center of the bundle, the X1 S uses a hand-crafted 1-inch true-condenser capsule and cardioid pickup pattern. Its 20 Hz to 20 kHz frequency range, 30 mV\/Pa sensitivity, and 9 dB(A) equivalent noise level support detailed capture of vocals and acoustic instruments. The cardioid response focuses on the source in front of the microphone while reducing pickup from the rear.\u003c\/p\u003e\u003cp\u003eThe X1 S is built to accommodate both subtle and high-output sources. Switchable -10 dB and -20 dB attenuation pads expand its usable range for close-miked amps, drums, and strong vocal performances. With the -20 dB pad selected, the microphone is rated to handle up to 160 dB SPL at 0.5% THD.\u003c\/p\u003e\u003cp\u003eTwo switchable low-cut filters, set at 80 Hz and 160 Hz, provide source-side control over rumble, footfall noise, and excessive proximity-effect bass. This makes the microphone easier to adapt to close vocal work, spoken-word recording, and instrument tracking. The all-metal body and gold-plated 3-pin XLR connector provide a durable wired signal path for studio use.\u003c\/p\u003e\u003cp\u003eThe RF-X Reflexion Filter adds portable acoustic control behind and around the microphone. Its four-layer construction uses a vented composite panel, wool fabric, an air gap, and acoustic foam to reduce unwanted room reflections. Together with the Isolation Pack and included 3-meter XLR cable, the bundle provides a useful front end for an audio interface, microphone preamp, or mixer that supplies 48V phantom power.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Recording Bundle:\u003c\/strong\u003e Includes the microphone, acoustic filter, shock mount, pop filter, and XLR cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Condenser Capsule:\u003c\/strong\u003e Captures vocals and instruments with a detailed cardioid response.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Handles up to 160 dB SPL with the -20 dB pad.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Pads:\u003c\/strong\u003e -10 dB and -20 dB settings help manage loud sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-Cut Filters:\u003c\/strong\u003e 80 Hz and 160 Hz options reduce rumble and excess bass.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRF-X Reflexion Filter:\u003c\/strong\u003e Helps reduce room reflections in untreated recording spaces.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe X1 S has an all-metal housing, a hand-crafted condenser capsule, and a gold-plated 3-pin male XLR connector. The included Isolation Pack uses a quick-release shock mount and removable, vertically adjustable metal pop filter. The RF-X is a hand-assembled, four-layer portable acoustic filter with a vented composite outer panel.\u003c\/p\u003e\u003cp\u003eConnect the included 3-meter XLR cable between the microphone and an audio interface, mixer, or microphone preamp that provides 48V phantom power. Mount the microphone in the supplied clip or Isolation Pack on a compatible mic stand, then position the RF-X behind the microphone for voice or instrument recording in an untreated room. Use the pads for high-output sources and select the low-cut filter as needed to reduce low-frequency buildup.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669493932102,"sku":"X1 S STUDIO BUNDLE","price":249.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61MxdVE0KHL.jpg?v=1784508456"}],"url":"https:\/\/audiowatt.store\/collections\/podcast-streaming-picks.oembed","provider":"Audio Watt Store","version":"1.0","type":"link"}