{"title":"Condenser Microphones","description":null,"products":[{"product_id":"rode-broadcaster-broadcast-condenser-microphone","title":"RØDE BROADCASTER Broadcast Condenser Microphone","description":"\u003cp\u003eThe RØDE BROADCASTER is a large-diaphragm condenser microphone made for broadcast speech, voice-over work, podcasting, and studio narration. Its end-address design helps presenters maintain a natural speaking position while recording directly into the microphone head. It is intended for systems where clear vocal capture and professional XLR connectivity are needed.\u003c\/p\u003e\u003cp\u003eA cardioid pickup pattern focuses on the speaker in front of the microphone while reducing pickup from the rear. The voice-tailored response and emphasized proximity effect can add perceived warmth and low-frequency weight when used close to the source. This makes it well suited to close-miked spoken-word applications.\u003c\/p\u003e\u003cp\u003eThe BROADCASTER uses a 1-inch HF2 capsule with a gold-plated diaphragm and JFET-based active electronics. Its 20 Hz to 20 kHz frequency range, 14 dB SPL equivalent noise rating, and 128 dB SPL maximum rating support detailed voice recording with useful headroom. An internal pop filter helps reduce plosive sounds before they reach the capsule.\u003c\/p\u003e\u003cp\u003eA switchable 75 Hz high-pass filter helps reduce low-frequency rumble from HVAC systems, traffic, vibration, and other environmental sources. The microphone also has an On-Air indicator LED for studio workflows. With the supplied 5-pin connector installed and wired to a compatible console, the LED can be controlled through switch contacts.\u003c\/p\u003e\u003cp\u003eThe BROADCASTER connects to a microphone preamp, mixer, audio interface, or broadcast console through XLR and requires phantom power. It can operate from 24V or 48V phantom power, although RØDE's operating guidance specifies a 48V phantom supply for normal use. The included stand mount, zip pouch, and On-Air indicator adaptor support studio installation and storage.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLarge 1-Inch Capsule:\u003c\/strong\u003e Supports detailed vocal capture for broadcast and voice-over work.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pattern:\u003c\/strong\u003e Prioritizes sound from the front of the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Pop Filter:\u003c\/strong\u003e Helps reduce plosive noise during close speech recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e75 Hz High-Pass Filter:\u003c\/strong\u003e Reduces low-frequency rumble and vibration when engaged.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOn-Air LED:\u003c\/strong\u003e Provides a visible live-microphone status indicator.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhantom-Powered XLR Output:\u003c\/strong\u003e Integrates with compatible professional audio equipment.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe BROADCASTER has a rugged stainless-steel body and a large-diaphragm, end-address condenser design. Its HF2 capsule uses a gold-plated diaphragm, while the active circuitry uses a JFET impedance converter with a bipolar output buffer. The microphone weighs 577 g and measures 167 mm long, 50 mm high, and 65 mm deep.\u003c\/p\u003e\u003cp\u003eMount the microphone lengthwise in the included RM2 stand mount and speak directly into the head. Connect it with an XLR microphone cable to equipment that supplies phantom power, then allow a brief stabilization period after power is applied. Use the rear high-pass filter switch when low-frequency noise is present; installation of the supplied 5-pin connector for console-controlled On-Air LED operation is best handled by an experienced audio or electronics technician.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668847059014,"sku":"BROADCASTER","price":405.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/518doUmIdyL.jpg?v=1784467158"},{"product_id":"rode-k2-multi-pattern-valve-condenser-microphone","title":"RØDE K2 Multi-Pattern Valve Condenser Microphone","description":"\u003cp\u003eThe RØDE K2 is a large-diaphragm valve condenser microphone built for detailed studio recording. It gives vocalists, musicians, producers, and engineers a flexible microphone option for capturing voices and acoustic instruments. Its side-address format and external power supply make it suited to a dedicated recording setup.\u003c\/p\u003e\u003cp\u003eA 1-inch gold-sputtered condenser capsule and hand-selected 6922 twin-triode valve form the core of the K2 design. The microphone is engineered to provide a rich, warm character while retaining the detail expected from a condenser microphone. Its low equivalent-noise rating also supports recording quieter sources and more nuanced performances.\u003c\/p\u003e\u003cp\u003eThe K2 uses a continuously variable polar-pattern control rather than a limited fixed-pattern switch. It can move from omnidirectional through cardioid to figure-8, allowing the pickup behavior to be matched to the room, source, and recording technique. Cardioid is useful for focusing on a source from the front, while omni and figure-8 expand the options for ambience, interviews, and stereo techniques.\u003c\/p\u003e\u003cp\u003eWith a 20Hz to 20kHz frequency range, 162dB SPL maximum handling, and 150dB dynamic range, the K2 is specified for a wide variety of recording levels. It connects through its dedicated power supply, which provides a balanced XLR output to a mixer, microphone preamp, or audio interface. The power supply also houses the polar-pattern control, ground-lift switch, and mains-voltage selector.\u003c\/p\u003e\u003cp\u003eThe K2 fits naturally into a studio system with a stable microphone stand, an XLR-equipped preamp or interface, and appropriate acoustic treatment. A shock mount is supplied, while a pop filter is recommended for vocal work to help reduce plosive sounds. The microphone includes a dedicated PSU arrangement instead of relying on standard 48V phantom power.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Gold-Sputtered Capsule:\u003c\/strong\u003e Large-diaphragm condenser design for detailed source capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6922 Twin-Triode Valve:\u003c\/strong\u003e Hand-selected tube supports the K2's valve microphone circuit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVariable Polar Pattern:\u003c\/strong\u003e Adjust from omni through cardioid to figure-8 at the PSU.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 10dBA equivalent noise supports quieter recording environments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Handles up to 162dB SPL for demanding sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDedicated Power Supply:\u003c\/strong\u003e Provides microphone power, pattern control, and balanced XLR output.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe K2 uses a side-address body with a 1-inch condenser capsule, valve impedance-converter electronics, and a satin nickel finish. Its Class-A valve circuitry uses a hand-selected and graded 6922 twin-triode valve. The microphone measures 208 x 55 x 55mm and has a net weight of 815g.\u003c\/p\u003e\u003cp\u003eMount the K2 securely on a stable microphone stand using the supplied shock mount, with the gold dot facing the sound source. Connect the microphone to its dedicated power supply with the supplied 7-pin cable, then connect the PSU's XLR output to a mixer, preamp, or audio interface. Set the PSU to the correct local mains voltage before use, allow the microphone a minute or two to stabilize, and use a pop filter for vocal recording.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668850663494,"sku":"K2","price":699.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/613-MsaDanL.jpg?v=1784467707"},{"product_id":"rode-m2-live-performance-condenser-vocal-microphone","title":"RØDE M2 Live Performance Condenser Vocal Microphone","description":"\u003cp\u003eThe RØDE M2 is a handheld condenser microphone built for live vocal performance. It provides a detailed, full-range vocal capture for singers, presenters, and performers using a PA system or professional audio mixer. Its focused pickup pattern helps keep the intended voice prominent in busy stage environments.\u003c\/p\u003e\u003cp\u003eDesigned for stage use, the M2 combines condenser-microphone detail with a tight supercardioid polar pattern. This pattern helps reduce spill from nearby instruments and stage monitors while supporting feedback-conscious microphone placement. It is well suited to live singing, spoken-word work, and presentations where vocal clarity matters.\u003c\/p\u003e\u003cp\u003eA 0.5-inch internally shock-mounted condenser capsule is at the center of the M2's design. The microphone covers a 35Hz to 20kHz frequency range and handles sound-pressure levels up to 141dB SPL. Its JFET impedance converter and bipolar output buffer support balanced operation with compatible professional audio equipment.\u003c\/p\u003e\u003cp\u003eThe M2 uses a rugged all-metal body intended for repeated live use. A built-in on\/off switch can be locked with its screw mechanism to help prevent accidental switching during a performance. The microphone also offers high RF rejection and low handling noise for practical stage operation.\u003c\/p\u003e\u003cp\u003eFor use in a system, connect the M2 to a balanced XLR microphone input that supplies 24V or 48V phantom power. It can be used with mixing consoles, PA systems, audio interfaces, and other compatible XLR-equipped equipment. An included mic clip and padded zip pouch help support transport and stand-mounted use.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCondenser Vocal Capsule:\u003c\/strong\u003e Captures detailed vocal sound for live performances and presentations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the performer and reduces surrounding spill.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternally Shock-Mounted Capsule:\u003c\/strong\u003e Helps reduce noise caused by handling and movement.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLockable On\/Off Switch:\u003c\/strong\u003e Helps prevent unintended switching during live use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAll-Metal Body:\u003c\/strong\u003e Provides a durable housing for regular stage handling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24V\/48V Phantom Power:\u003c\/strong\u003e Works with compatible mixers and interfaces providing phantom power.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe M2 has a black, heavy-duty all-metal body with an end-address design and a 47mm diameter. Its 0.5-inch condenser capsule is internally shock-mounted, while the integrated switch includes a locking screw. The microphone weighs 308g and measures 187mm long.\u003c\/p\u003e\u003cp\u003eConnect the M2 using a standard balanced 3-pin XLR microphone cable to an input that provides P24 or P48 phantom power. Use the included RM3 mic clip for stand mounting, and aim the front of the microphone toward the vocalist while positioning monitors outside the supercardioid pickup area. The included padded zip pouch is useful for storage and transport.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668850892870,"sku":"M2-RODE","price":170.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/610SN1aEVvL.jpg?v=1784467738"},{"product_id":"rode-nt1000-large-diaphragm-condenser-microphone","title":"RØDE NT1000 Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe RØDE NT1000 is a side-address, large-diaphragm studio condenser microphone for recording vocals and acoustic or amplified instruments. It gives creators a dedicated XLR microphone option for studio setups that need detailed capture without USB-only limitations. Its fixed cardioid pickup pattern focuses on the source in front of the microphone while reducing pickup from the rear.\u003c\/p\u003e\u003cp\u003eThis microphone suits home studios, project studios, musicians, voice talent, and engineers recording a range of sources. RØDE specifies it for vocals and instruments, including piano and drum-overhead use. The wide 20Hz to 20kHz frequency range supports full-spectrum recording applications.\u003c\/p\u003e\u003cp\u003eThe NT1000 combines a 1-inch HF2 capsule with an externally biased true-condenser design. Its low 6dBA equivalent noise level is useful when recording quieter sources or working with more gain. The cardioid pattern and 100-ohm output impedance make it a practical fit for standard microphone preamps.\u003c\/p\u003e\u003cp\u003eInside, the NT1000 uses transformerless circuitry with a unity-gain closed-loop impedance converter, JFET input, and bipolar buffering. RØDE also incorporates internal capsule shock mounting to help isolate the capsule from handling and stand-borne vibration. The microphone is rated for up to 140dB SPL, allowing it to accommodate demanding sound sources when paired with appropriate input gain.\u003c\/p\u003e\u003cp\u003eUse the NT1000 with an audio interface, mixer, or microphone preamp that provides 24V or 48V phantom power through a balanced 3-pin XLR connection. The included RM2 stand mount supports placement on compatible microphone stands. It can serve as a primary studio vocal microphone or as a versatile addition alongside specialized dynamic, small-diaphragm, or multi-pattern microphones.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch HF2 Capsule:\u003c\/strong\u003e Large-diaphragm condenser capsule supports detailed studio recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the front source and reduces rear pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 6dBA equivalent noise supports quieter recording situations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTransformerless Electronics:\u003c\/strong\u003e JFET-based circuitry provides a balanced XLR microphone output.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Rated for sound-pressure levels up to 140dB SPL.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Shock Mounting:\u003c\/strong\u003e Helps reduce vibration reaching the microphone capsule.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT1000 has a durable satin-nickel finish, a high-strength welded and heat-treated mesh head, and a 1-inch gold-sputtered capsule. Its cylindrical side-address body measures 54mm wide by 209mm high and weighs 682g. The internal capsule suspension is integrated into the microphone body rather than being a separate external shock mount.\u003c\/p\u003e\u003cp\u003eMount the NT1000 in the included RM2 stand mount on a stable microphone stand; the mount includes a 3\/8-inch to 5\/8-inch thread adaptor. Connect it to a balanced 3-pin XLR microphone input and enable P24 or P48 phantom power from a properly functioning interface, mixer, or preamp. For vocal work, use a suitable pop filter and position the microphone's front toward the sound source; for instruments, adjust placement before relying on EQ.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668851679302,"sku":"NT1000","price":339.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61HasQPSZtL.jpg?v=1784467776"},{"product_id":"rode-nt1gen5b-1-inch-usb-xlr-condenser-microphone","title":"RØDE NT1GEN5B 1-Inch USB\/XLR Condenser Microphone","description":"\u003cp\u003eThe RØDE NT1GEN5B is a large-diaphragm studio condenser microphone designed for vocal recording, instruments, voiceovers, podcasting, and home-studio production. Its Dual Connect design gives creators a choice between traditional analog XLR operation and direct USB-C recording to a computer. This flexibility helps simplify a first recording setup while keeping a path open for use with an audio interface or mixer.\u003c\/p\u003e\u003cp\u003eIts 1-inch HF6 condenser capsule uses a cardioid pickup pattern that focuses on sound in front of the microphone while reducing pickup from behind it. The side-address design is intended for placing the front of the microphone, marked by its gold dot, toward the performer or sound source. With a 20Hz–20kHz frequency range, 4dBA equivalent noise rating, and 142 dB SPL maximum rating, it is equipped for quiet detail as well as loud sources.\u003c\/p\u003e\u003cp\u003eWhen connected by XLR, the NT1GEN5B functions as an analog condenser microphone and requires 48V phantom power from a compatible preamp, mixer, or interface. The XLR output is a conventional 3-pin connection with 100-ohm output impedance. This mode is useful for studio systems that already have microphone preamps and balanced XLR inputs.\u003c\/p\u003e\u003cp\u003eUSB-C mode adds a built-in Revolution Preamp, digital conversion up to 192kHz, and 24-bit or 32-bit floating-point recording support. The microphone can connect directly to a compatible Mac or Windows computer without an external audio interface. Its onboard DSP supports APHEX processing tools including a compressor, noise gate, high-pass filter, Aural Exciter, and Big Bottom when used at 48kHz.\u003c\/p\u003e\u003cp\u003eThe NT1GEN5B includes the SM6 shock mount with pop filter, a 3m USB-C cable, a 6m XLR cable, and a dust cover. The shock mount helps reduce vibration and handling noise, while the adjustable pop filter helps control vocal plosives. It is a practical choice for creators who want one microphone that can work in a direct-to-computer setup today and in an XLR-based studio system later.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual Connect Output:\u003c\/strong\u003e Use either analog XLR or direct USB-C computer connectivity.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch HF6 Capsule:\u003c\/strong\u003e Large-diaphragm cardioid design captures focused studio recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 4dBA equivalent noise supports detailed quiet-source recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e32-Bit Float USB:\u003c\/strong\u003e Provides expanded level recovery flexibility in compatible software.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt-In DSP:\u003c\/strong\u003e Enables APHEX processing through compatible RØDE software.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Recording Kit:\u003c\/strong\u003e Includes shock mount, pop filter, XLR cable, USB-C cable, and dust cover.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT1GEN5B has a rugged aluminum body with a black high-grade finish. Its HF6 capsule is internally shock-mounted to help reduce external vibration reaching the capsule. The microphone measures 189mm high by 52mm wide and 52mm deep, with a weight of 308g.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included SM6 shock mount on a compatible microphone stand or studio arm; the mount supports 3\/8-inch and 5\/8-inch threads. Point the gold dot toward the performer and place the pop filter between the source and capsule for vocal work. Connect by XLR to equipment providing 48V phantom power, or use the included USB-C cable for direct computer recording; XLR and USB cannot be used simultaneously.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668852662342,"sku":"NT1GEN5B","price":213.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51-vfZouwQL.jpg?v=1784467897"},{"product_id":"rode-nt1signatureblack-studio-condenser-microphone","title":"RØDE NT1SIGNATUREBLACK Studio Condenser Microphone","description":"\u003cp\u003eThe RØDE NT1 Signature Series is a large-diaphragm XLR condenser microphone for studio recording, streaming, podcasting and voice-over work. It is designed for creators who want a dedicated studio microphone rather than a USB microphone, using an audio interface or mixer as the connection to a computer. The Black NT1SIGNATUREBLACK package includes the microphone, SM6 shock mount, pop filter and XLR cable.\u003c\/p\u003e\u003cp\u003eIts cardioid pickup pattern focuses on sound arriving at the front of the microphone while reducing pickup from behind it. This makes it well suited to close-miked vocals, spoken word and single-instrument recording in a treated or reasonably controlled room. The gold dot on the microphone body identifies the front, helping users position it correctly toward the sound source.\u003c\/p\u003e\u003cp\u003eThe NT1 Signature Series uses RØDE's HF6 1-inch true condenser capsule and a side-address design. Its stated 20 Hz to 20 kHz frequency range, 25 mV\/Pa sensitivity and 4 dBA equivalent noise support detailed recording of quiet vocal passages and acoustic instruments. The microphone is specified for sound-pressure levels up to 142 dB SPL, providing headroom for louder sources when used with appropriate gain settings.\u003c\/p\u003e\u003cp\u003eConnection is through a standard 3-pin XLR output, so the microphone requires an XLR-equipped mixer, audio interface or similar device. It also requires 48V phantom power supplied through the XLR connection. This makes the NT1 Signature Series a practical fit for recording systems built around an interface, mixer or production console rather than direct USB operation.\u003c\/p\u003e\u003cp\u003eThe included SM6 mount helps isolate the microphone from stand-borne movement and includes a pop filter for reducing plosive bursts from vocal performance. The mount fits standard microphone stands and studio arms with 5\/8-inch or 3\/8-inch threads, and it can be used upright or inverted. This package provides the essential microphone-side accessories, while the recording interface, stand or arm, headphones and computer software are selected separately.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHF6 1-Inch Capsule:\u003c\/strong\u003e True condenser capsule captures detailed vocal and instrument recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pattern:\u003c\/strong\u003e Focuses on the front sound source and rejects rear pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4 dBA Equivalent Noise:\u003c\/strong\u003e Supports clean recording of quieter performances and speech.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e142 dB SPL Handling:\u003c\/strong\u003e Accommodates louder sound sources with substantial headroom.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eXLR Studio Connection:\u003c\/strong\u003e Integrates with compatible mixers and audio interfaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Accessory Package:\u003c\/strong\u003e Includes SM6 shock mount, pop filter and XLR cable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT1 Signature Series has a rugged aluminium body with a high-grade finish designed to resist scuffs and scratches. Its 52 x 52 x 189 mm housing weighs 313 g, and the side-address layout uses a gold dot to mark the recording side. RØDE designs and makes the microphone in its precision manufacturing facilities in Sydney, Australia.\u003c\/p\u003e\u003cp\u003eInstall the microphone in the included SM6 shock mount on a compatible stand or studio arm, point the gold dot toward the performer, and place the pop filter between the performer and capsule. Connect the included XLR cable to an interface, mixer or comparable device, reduce input level before connection, then enable 48V phantom power where required. For computer recording, use the interface as the bridge to recording software.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668867211334,"sku":"NT1SIGNATUREBLACK","price":140.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71mmZOQPuNL.jpg?v=1784467937"},{"product_id":"rode-nt1signatureblue-1-inch-xlr-condenser-microphone","title":"RØDE NT1SIGNATUREBLUE 1-Inch XLR Condenser Microphone","description":"\u003cp\u003eThe RØDE NT1 Signature Series is a large-diaphragm studio condenser microphone designed for vocals, instruments, voice-over work, streaming and podcasting. This blue NT1SIGNATUREBLUE version uses an analog XLR connection rather than USB. It is intended for creators who want a dedicated studio microphone that connects to an audio interface, mixer or console with phantom power.\u003c\/p\u003e\u003cp\u003eIts 1-inch HF6 true condenser capsule combines a smooth 20Hz–20kHz frequency range with a tight cardioid pickup pattern. The result is a focused capture of the source in front of the microphone while helping reduce sound arriving from behind it. Its sound character is described by RØDE as warm in the low end, detailed through the midrange and clear in the highs.\u003c\/p\u003e\u003cp\u003eThe NT1 Signature Series has a 4dBA equivalent noise rating, which is useful when recording quieter vocals, acoustic instruments and spoken-word sources. Its sensitivity is rated at 25mV\/Pa at 94dB SPL, helping it provide a healthy output to a suitable microphone preamp. A 142dB SPL maximum rating also supports close recording of louder sources such as drums, percussion and amplified instruments.\u003c\/p\u003e\u003cp\u003eThis is an XLR condenser microphone, so it requires 48V phantom power from a compatible audio interface, mixer or preamp. The included XLR cable carries both the analog signal and phantom power connection. It is a practical fit for home studios, production rooms and desktop recording setups built around an interface or mixer.\u003c\/p\u003e\u003cp\u003eThe package includes the SM6 studio shock mount and detachable pop filter to help address vibration, handling noise and vocal plosives. The mount can be used on a standard microphone stand or studio arm, allowing the microphone to be positioned upright or inverted. That included accessory set makes it straightforward to add the NT1 Signature Series to an existing XLR recording chain.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHF6 1-Inch Capsule:\u003c\/strong\u003e True condenser design captures detailed vocals and instruments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the front source and rejects rear sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4dBA Equivalent Noise:\u003c\/strong\u003e Supports clean recording of quiet performances.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e142dB SPL Handling:\u003c\/strong\u003e Accommodates loud instruments and close-miked sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eXLR Output:\u003c\/strong\u003e Connects to compatible interfaces, mixers and microphone preamps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded SM6 Kit:\u003c\/strong\u003e Provides shock isolation, pop filtering and cable connection.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT1 Signature Series has a rugged high-grade aluminum body with a durable blue finish designed to resist scuffs and scratches. It is a side-address microphone, and the gold dot on the body identifies the front of the capsule. The microphone measures 189mm high by 52mm wide and weighs 313g.\u003c\/p\u003e\u003cp\u003eInstall the microphone in the included SM6 shock mount, orienting its gold dot toward the pop filter and sound source. The SM6 fits standard microphone stands and studio arms with 5\/8-inch or 3\/8-inch threads, and can be used upright or upside down. Connect the included XLR cable to a compatible input, lower the input gain before connection, then enable 48V phantom power on the connected device.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668874125382,"sku":"NT1SIGNATUREBLUE","price":159.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71RlJIg59XL.jpg?v=1784467978"},{"product_id":"rode-nt1signaturered-large-diaphragm-condenser-microphone","title":"RØDE NT1SIGNATURERED Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe RØDE NT1 Signature Series is a large-diaphragm, side-address condenser microphone designed for studio recording, streaming, podcasting and voice-over work. This red NT1SIGNATURERED version uses a conventional 3-pin XLR output, making it suited to audio interfaces, mixers and other equipment with a phantom-powered microphone input. It provides a focused recording solution for creators who need a dedicated studio microphone rather than a USB microphone.\u003c\/p\u003e\u003cp\u003eThe microphone uses a tight cardioid pickup pattern that emphasizes sound in front of the capsule while reducing pickup from behind the microphone. This makes it useful for vocals, spoken-word recording, acoustic instruments and close-miked sources in home or project studios. The gold dot identifies the front of the side-address microphone for correct placement.\u003c\/p\u003e\u003cp\u003eIts HF6 1-inch true condenser capsule is paired with a smooth 20Hz–20kHz frequency range and 25mV sensitivity at 94dB SPL. RØDE describes the tonal character as warm in the low end, detailed through the midrange and open at the top. A 4dBA A-weighted equivalent-noise specification helps preserve low-level detail when recording quiet voices or instruments.\u003c\/p\u003e\u003cp\u003eThe NT1 Signature Series handles sound-pressure levels up to 142dB SPL, allowing it to cover both softer sources and louder instruments. Its JFET impedance converter with bipolar output buffer is designed for an XLR studio signal path. It requires 48V phantom power supplied through the connected XLR cable by a compatible mixer or audio interface.\u003c\/p\u003e\u003cp\u003eThis package includes the SM6 shock mount, an adjustable pop filter and an XLR cable, providing the key accessories needed to mount and connect the microphone. The shock mount helps reduce transmitted vibration, while the pop filter helps control plosive air bursts during vocal recording. It is a practical fit for a first XLR recording chain or as a dedicated vocal and instrument microphone within an existing setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHF6 1-Inch Capsule:\u003c\/strong\u003e True condenser capsule captures detailed studio recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the source and reduces rear pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e4dBA Equivalent Noise:\u003c\/strong\u003e Supports clean recording of quiet sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e142dB SPL Handling:\u003c\/strong\u003e Accommodates loud vocals and instruments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eXLR Studio Connection:\u003c\/strong\u003e Works with compatible mixers and audio interfaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded SM6 Accessory Kit:\u003c\/strong\u003e Adds isolation, plosive control and XLR connectivity.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT1 Signature Series has a rugged high-grade aluminum body with a durable finish, and this version is finished in red. It is designed and made in RØDE's precision manufacturing facilities in Sydney, Australia. The microphone measures 52 x 52 x 189mm and weighs 313g.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included SM6 shock mount on a standard microphone stand or studio arm, using its 5\/8-inch or 3\/8-inch mounting thread. Position the gold dot toward the performer and place the pop filter between the source and capsule for vocal work. Connect the included XLR cable to an interface or mixer, turn its input level down before connection, then enable 48V phantom power as required.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668875337798,"sku":"NT1SIGNATURERED","price":148.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71waedd57nL.jpg?v=1784468018"},{"product_id":"rode-nt1signaturewhite-large-diaphragm-condenser-microphone","title":"RØDE NT1SIGNATUREWHITE Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe RØDE NT1SIGNATUREWHITE is a large-diaphragm studio condenser microphone designed for vocal recording, instruments, voice-over work, podcasting and streaming. Its analog XLR connection makes it a practical choice for home studios and production spaces using a mixer or audio interface. The white finish gives creators an option that can complement brighter studio and desktop setups.\u003c\/p\u003e\u003cp\u003eA 1-inch HF6 true condenser capsule and cardioid pickup pattern help focus capture on the intended source while reducing pickup from the rear of the microphone. The side-address design is suited to vocalists, acoustic instruments and spoken-word recording. Its 20 Hz to 20 kHz frequency range supports full-range recording applications.\u003c\/p\u003e\u003cp\u003eThe NT1 Signature Series is specified with an equivalent self-noise rating of 4 dBA and a maximum SPL rating of 142 dB SPL. This combination supports both quieter sources and louder performances when the connected preamp is set appropriately. The microphone has a stated sensitivity of 25 mV at 94 dB SPL.\u003c\/p\u003e\u003cp\u003eIts active circuitry uses a JFET impedance converter with a bipolar output buffer, and the microphone provides a balanced 3-pin XLR output. It requires 48V phantom power from a compatible audio interface, mixer or preamp. This makes it an appropriate upgrade for users moving from USB microphones to an XLR-based recording chain.\u003c\/p\u003e\u003cp\u003eThe included SM6 shock mount, pop filter and XLR cable provide the core accessories needed to build a recording setup. The shock mount helps isolate the microphone from stand-borne vibration, while the pop filter helps manage plosive bursts during close vocal work. Add a stable microphone stand or boom arm and a phantom-powered XLR input to complete the system.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHF6 1-Inch Capsule:\u003c\/strong\u003e Large true-condenser capsule captures detailed vocal and instrument recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses on sound in front while reducing rear pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 4 dBA equivalent noise supports clean recordings of quieter sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Rated to handle sources up to 142 dB SPL.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAnalog XLR Output:\u003c\/strong\u003e Connects to compatible mixers, preamps and audio interfaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Accessory Kit:\u003c\/strong\u003e Includes SM6 shock mount, pop filter and XLR cable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT1SIGNATUREWHITE has a rugged aluminum body with a high-grade, scratch-resistant white finish. It measures 52 mm wide by 52 mm long and 189 mm high, with a microphone weight of 313 g. RØDE designs and manufactures the NT1 Signature Series in its Sydney, Australia facilities.\u003c\/p\u003e\u003cp\u003eMount the microphone in the supplied SM6 shock mount with the gold dot facing the sound source and pop filter. The SM6 can attach to a standard microphone stand or studio arm using its 5\/8-inch or 3\/8-inch thread options. Connect the included XLR cable to a mixer or audio interface, lower the input level before connection, and enable 48V phantom power only after the system is connected.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668875567174,"sku":"NT1SIGNATUREWHITE","price":159.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51z94xoS-VL.jpg?v=1784468060"},{"product_id":"rode-nt2000-large-diaphragm-condenser-microphone","title":"Rode NT2000 Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe Rode NT2000 is a side-address, large-diaphragm condenser microphone built for studio recording applications that require adaptable pickup behavior. Its continuously variable controls let one microphone cover close vocal work, instrument recording, room capture, and stereo techniques that use a figure-8 pattern. It connects to a mixer, microphone preamp, or audio interface through a balanced 3-pin XLR output.\u003c\/p\u003e\u003cp\u003eThis microphone is suited to recording musicians, voice talent, producers, and home-studio users who need more control than a fixed-cardioid condenser provides. The polar-pattern dial moves continuously from omnidirectional through cardioid to figure-8, helping tailor room pickup and off-axis rejection to the source. A gold dot identifies the front of the microphone for cardioid positioning.\u003c\/p\u003e\u003cp\u003eThe NT2000 has a 20Hz to 20kHz frequency range, 7dBA equivalent noise level, and a 140dB dynamic range. Its high maximum SPL rating supports both quiet detailed sources and louder sound sources when placement and gain are set appropriately. The variable pad can reduce the level entering the microphone's internal preamp by up to 10dB.\u003c\/p\u003e\u003cp\u003eRode uses a 1-inch externally polarised dual-diaphragm condenser capsule with gold sputtering, along with transformerless surface-mount electronics. The microphone uses a JFET impedance converter with a bipolar output buffer and has internal capsule shock mounting. A continuously variable high-pass filter lets the user select a low-frequency cutoff point from 20Hz to 150Hz.\u003c\/p\u003e\u003cp\u003eUse the NT2000 as the main microphone in an XLR-based recording chain with an interface or preamp that supplies P24 or P48 phantom power. Its included SM2 shock mount supports more isolated stand mounting, while the variable controls make it practical as a flexible upgrade for a studio that records different sources. The microphone is also supplied with an RC1 carry case according to the manufacturer datasheet.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVariable Polar Pattern:\u003c\/strong\u003e Sweep continuously between omni, cardioid, and figure-8 pickup modes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Dual Diaphragm:\u003c\/strong\u003e Gold-sputtered condenser capsule supports detailed studio recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVariable Pad:\u003c\/strong\u003e Adjust attenuation continuously from 0dB to -10dB.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVariable High-Pass Filter:\u003c\/strong\u003e Set low-frequency reduction from 20Hz to 150Hz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Equivalent Noise:\u003c\/strong\u003e 7dBA self-noise supports quieter recording sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Shock Mounting:\u003c\/strong\u003e Helps reduce vibration reaching the microphone capsule.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT2000 uses a silver-finished body with a high-strength welded, heat-treated steel mesh head. Its 25mm dual-diaphragm capsule is internally shock mounted, and the microphone measures 208mm long by 55mm in diameter. Net weight is 831g, so use a stable microphone stand or boom with adequate support.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included SM2 shock mount, connect a balanced 3-pin XLR cable, and apply P24 or P48 phantom power only after cable connections are made. Start with the pad at 0dB and the high-pass filter at its lowest setting, then adjust for source level and unwanted low-frequency noise. For cardioid use, point the gold-dot side toward the desired sound source; use omni or figure-8 when their wider or bidirectional pickup patterns suit the recording setup.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668875599942,"sku":"NT2000","price":619.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51QAmgceD8L.jpg?v=1784468098"},{"product_id":"rode-nt2-a-multi-pattern-studio-condenser-microphone","title":"RØDE NT2-A Multi-Pattern Studio Condenser Microphone","description":"\u003cp\u003eThe RØDE NT2-A is a wired large-diaphragm condenser microphone for studio recording. It is designed for creators who need one microphone to cover vocals, instruments, voice work, and room recording setups. Its selectable pickup patterns help adapt the microphone to the source and recording environment.\u003c\/p\u003e\u003cp\u003eA 1-inch gold-sputtered dual-diaphragm capsule captures a 20 Hz to 20 kHz frequency range. The microphone has a 7 dBA equivalent noise level and a sensitivity of 16 mV at 94 dB SPL, supporting detailed recording with low self-noise. Its side-address format makes it suitable for conventional studio-mic positioning.\u003c\/p\u003e\u003cp\u003eThe NT2-A provides cardioid, omnidirectional, and figure-8 polar patterns from controls on the microphone body. Cardioid is useful when focusing on a source in front of the microphone, omnidirectional captures sound around it, and figure-8 picks up from the front and rear. This flexibility supports solo recording, room capture, and two-person face-to-face setups.\u003c\/p\u003e\u003cp\u003eSelectable 40 Hz and 80 Hz high-pass filters help reduce low-frequency rumble when needed. A three-position pad offers 0 dB, -5 dB, and -10 dB settings for working with louder sources. The microphone handles up to 147 dB SPL normally and up to 157 dB SPL with the maximum pad setting.\u003c\/p\u003e\u003cp\u003eJFET impedance-converter electronics with a bipolar output buffer feed a balanced XLR output. The NT2-A is intended for use with an XLR microphone preamp, audio interface, mixer, or recorder that provides compatible phantom power. It includes an SM6 shock mount and XLR cable, providing a practical foundation for a studio microphone setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch HF1 Capsule:\u003c\/strong\u003e Gold-sputtered dual-diaphragm design supports full-range studio recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree Polar Patterns:\u003c\/strong\u003e Choose cardioid, omnidirectional, or figure-8 pickup on the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-Pass Filter:\u003c\/strong\u003e Flat, 40 Hz, and 80 Hz settings help manage low-frequency rumble.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Pad:\u003c\/strong\u003e 0 dB, -5 dB, and -10 dB options accommodate louder sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e The 7 dBA equivalent noise rating suits detailed recording work.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced XLR Output:\u003c\/strong\u003e Connects to compatible microphone preamps, mixers, and audio interfaces.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT2-A uses a silver side-address body with an internally shock-mounted capsule. Its transformerless surface-mount circuitry uses a JFET impedance converter with a bipolar output buffer. The microphone measures 209 mm long by 55 mm in diameter and weighs 860 g.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included SM6 shock mount on a stable microphone stand or studio arm, then connect the included XLR cable to a compatible preamp, mixer, recorder, or audio interface. Enable P24 or P48 phantom power from the connected device before use. Select the polar pattern, high-pass filter, and pad according to the source, room, and recording level.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668877893702,"sku":"NT2A","price":335.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61_XZ2kxbHL.jpg?v=1784468449"},{"product_id":"rode-nt3-3-4-inch-cardioid-condenser-microphone","title":"RØDE NT3 3\/4-Inch Cardioid Condenser Microphone","description":"\u003cp\u003eThe RØDE NT3 is a wired 3\/4-inch condenser microphone designed for studio recording, live performance, and location sound work. It provides a detailed, full-range capture option for vocals, instruments, guitar amplifiers, drums, and spoken-word recording. Its XLR output makes it suited to mixers, audio interfaces, microphone preamps, and field recorders.\u003c\/p\u003e\u003cp\u003eThis microphone is made for users who need condenser-microphone detail without being limited to a phantom-powered studio setup. The NT3 can operate from compatible P12, P24, or P48 phantom power, or from an internal 9V battery. That dual-power design is useful when recording with equipment that does not supply phantom power.\u003c\/p\u003e\u003cp\u003eThe NT3 uses an externally polarized 0.75-inch condenser capsule and JFET impedance-converter electronics with a bipolar output buffer. Its published 20Hz to 20kHz frequency response, 12mV\/Pa sensitivity, and low equivalent-noise rating support clear capture across a broad range of sources. A transformerless balanced output is designed for connection to professional XLR audio equipment.\u003c\/p\u003e\u003cp\u003eBuilt for regular studio and field use, the microphone has a cast-metal body with a satin-nickel finish and a durable mesh head. Internal capsule shock mounting helps reduce vibration transferred through a stand or boom. RØDE also specifies a high level of RF rejection for use around common electronic equipment.\u003c\/p\u003e\u003cp\u003eThe NT3 can be handheld, placed on a microphone stand, or used on a boompole when paired with appropriate mounting hardware. It is a practical upgrade for creators moving from basic dynamic microphones to a more sensitive condenser design. For a complete recording chain, connect it with a balanced XLR cable to a preamp, mixer, recorder, or audio interface with sufficient gain.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.75-Inch Condenser Capsule:\u003c\/strong\u003e Externally polarized capsule captures detailed sound across a wide frequency range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual Power Operation:\u003c\/strong\u003e Runs from phantom power or an internal 9V battery.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced XLR Output:\u003c\/strong\u003e Connects to professional mixers, interfaces, recorders, and microphone preamps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-Noise Electronics:\u003c\/strong\u003e Published 16dBA equivalent-noise level supports quieter recording environments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Shock Mounting:\u003c\/strong\u003e Helps reduce vibration reaching the capsule during stand-mounted use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMetal Construction:\u003c\/strong\u003e Cast-metal body and mesh head support studio, stage, and location use.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT3 has a cast-metal body finished in satin nickel, along with a high-strength welded and heat-treated mesh head. Its internal capsule shock-mounting system is intended to reduce mechanical vibration, while the transformerless output and audio-grade surface-mount components support a professional wired signal path. The microphone weighs 371g without its battery and measures 206mm long by 32mm in diameter.\u003c\/p\u003e\u003cp\u003eConnect the NT3 to a microphone input with a standard balanced 3-pin XLR cable. Use P12, P24, or P48 phantom power when available, or install a correctly polarized 9V PP3 battery when phantom power is unavailable; RØDE recommends alkaline or lithium batteries. The included RM3 stand mount, WS3 windshield, and ZP1 zip pouch support common stand-mounted and portable recording setups.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668877926470,"sku":"NT3","price":269.96,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51UeRRMkulL.jpg?v=1784468485"},{"product_id":"rode-nt4-x-y-stereo-condenser-microphone","title":"RØDE NT4 X\/Y Stereo Condenser Microphone","description":"\u003cp\u003eThe RØDE NT4 is a stereo condenser microphone built for capturing a coherent left-right image without assembling a separate matched microphone pair. Its fixed X\/Y capsule arrangement gives creators a practical way to record stereo sources with consistent placement and channel alignment. It is suited to studio work, field recording, camera-based recording, and portable-recorder setups.\u003c\/p\u003e\u003cp\u003eTwo closely matched 1\/2-inch cardioid condenser capsules are positioned in a 90-degree X\/Y configuration. This arrangement captures stereo width while retaining a focused forward pickup pattern that helps reduce sound arriving from behind the microphone. It is useful for drum overheads, percussion, ensembles, choir vocals, ambience, sound design, and foley.\u003c\/p\u003e\u003cp\u003eThe NT4 covers a 20 Hz to 20 kHz frequency range and handles sound-pressure levels up to 143 dB SPL. Its 16 dBA equivalent noise level, 128 dB-plus dynamic range, and cardioid capsules support detailed recording across quiet and high-level sources. The microphone uses a JFET impedance converter with a bipolar output buffer.\u003c\/p\u003e\u003cp\u003eFor flexible operation, the NT4 runs from P48 phantom power or a 9V battery. This lets it connect to mixers and audio interfaces with phantom power, while also supporting portable recorders and compatible cameras when battery operation is needed. A dual-XLR cable and a 3.5mm mini-jack cable are included for these different connection approaches.\u003c\/p\u003e\u003cp\u003eThe NT4 provides a fixed stereo array in one microphone body, simplifying setup compared with separate microphones, a stereo bar, and extra alignment work. It can be mounted with the included RM3 mic clip and used with the included WS4 windshield when appropriate. Its supplied padded zip pouch helps keep the microphone and accessories together between sessions.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFixed 90-Degree X\/Y Array:\u003c\/strong\u003e Creates stereo capture from a single microphone body.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched 1\/2-Inch Capsules:\u003c\/strong\u003e Supports consistent left and right channel response.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup:\u003c\/strong\u003e Focuses on sound in front of the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual Power Options:\u003c\/strong\u003e Operates from P48 phantom power or a 9V battery.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Stereo Cables:\u003c\/strong\u003e Connects to mixers, recorders, and compatible cameras.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Accommodates loud sources up to 143 dB SPL.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT4 uses a pressure-gradient condenser design with dual externally biased capsules, gold-sputtered diaphragms, surface-mount circuitry, and a satin-nickel finish. Its end-address body measures 231 mm long and 41 mm in diameter, with a net weight of 480 g. The microphone incorporates an on\/off switch and a red battery-status LED for battery-powered operation.\u003c\/p\u003e\u003cp\u003eMount the NT4 securely to a stable microphone stand using the included RM3 clip, then rotate the microphone to aim the fixed X\/Y capsule pair toward the sound source. Use the included dual-XLR cable for two mixer or recorder channels, panned left and right, or use the included 3.5mm cable with a compatible recorder or camera input. Power the microphone with P48 phantom power or fit a 9V PP3 battery when phantom power is unavailable.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668878057542,"sku":"NT4","price":529.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61Zx6JTBjVL.jpg?v=1784468526"},{"product_id":"rode-nt5-small-diaphragm-condenser-microphone","title":"RØDE NT5 Small-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe RØDE NT5 is a small-diaphragm condenser microphone built for detailed recording duties in studios, live setups, and location workflows. It gives musicians, engineers, and content creators a focused microphone option for capturing acoustic instruments, percussion, cymbals, and spoken dialogue. Its cardioid pickup pattern helps emphasize the source in front of the microphone while reducing pickup from the rear.\u003c\/p\u003e\u003cp\u003eA 1\/2-inch gold-sputtered cardioid condenser capsule provides the NT5's balanced, full-range response. The microphone covers a 20 Hz to 20 kHz frequency range, making it suitable for sources that need natural high-frequency detail and low-frequency extension. With a maximum SPL rating of 143 dB SPL, it can also accommodate louder instruments and close-miked percussion.\u003c\/p\u003e\u003cp\u003eThe NT5 uses a pressure-gradient acoustic design and an externally biased condenser capsule. Its 16 dBA equivalent noise level supports clean recording in quieter environments when paired with an appropriate microphone preamp. The 100-ohm output impedance and balanced XLR connection support integration with standard professional audio equipment.\u003c\/p\u003e\u003cp\u003eThis microphone is a practical choice for recording acoustic guitar, drum overheads, cymbals, piano, strings, room sound, and dialogue. Its end-address form factor is compact enough for close placement where a larger microphone may be difficult to position. The included microphone clip, foam windshield, and padded zip pouch support regular studio and portable use.\u003c\/p\u003e\u003cp\u003eThe NT5 is sold individually under model NT5, and RØDE also offers the microphone as a certified matched pair for stereo recording. An optional NT45-O omnidirectional capsule can expand the system for applications that call for omnidirectional pickup. It requires phantom power from a compatible mixer, audio interface, recorder, or microphone preamp.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1\/2-Inch Gold-Sputtered Capsule:\u003c\/strong\u003e Captures detailed sound with a cardioid response.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses on the intended source from the front.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWide Frequency Range:\u003c\/strong\u003e Covers frequencies from 20 Hz to 20 kHz.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Equivalent Noise:\u003c\/strong\u003e Rated at 16 dBA for cleaner recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Handles up to 143 dB SPL.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExpandable Capsule System:\u003c\/strong\u003e Supports the optional NT45-O omnidirectional capsule.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT5 has a compact 118 x 20 x 20 mm body with a heavy-duty satin-nickel plated finish. Its small-diaphragm, end-address design is intended for precise placement on microphone stands, stereo bars, booms, and other standard microphone-mounting solutions. The microphone weighs 100 g, helping keep stand and boom setups manageable.\u003c\/p\u003e\u003cp\u003eConnect the NT5 to a balanced 3-pin XLR microphone input and enable P48 phantom power on the connected preamp, mixer, recorder, or audio interface. Use the included RM5 microphone clip for stand mounting and the included WS5 windshield when light wind or breath noise is a concern. For stereo techniques, use two NT5 microphones in a suitable stereo array; the NT5 is also available from RØDE as a certified matched pair.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668878516294,"sku":"NT5","price":219.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/413pcAu_FRL.jpg?v=1784468558"},{"product_id":"rode-nt55-multi-pattern-small-diaphragm-condenser-microphone","title":"RØDE NT55 Multi-Pattern Small-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe RØDE NT55 is a small-diaphragm true condenser microphone for detailed recording of instruments, ensembles, ambience, and sound sources where placement flexibility matters. It provides interchangeable cardioid and omnidirectional capsules, allowing one microphone body to serve different recording approaches. Its balanced XLR output and P48 phantom-power operation make it suited to studio interfaces, mixers, recorders, and professional preamps.\u003c\/p\u003e\u003cp\u003eThis microphone is designed for musicians, engineers, content creators, and location recordists who need a compact condenser with switchable pickup patterns. The cardioid capsule helps focus on a source while reducing sound arriving from the rear, while the omnidirectional capsule offers a broader, more open capture. This makes the NT55 useful for acoustic instruments, drum overheads, room capture, stereo techniques, and live or broadcast applications.\u003c\/p\u003e\u003cp\u003eThe NT55 uses a 0.5-inch externally biased, gold-sputtered condenser capsule and a JFET impedance converter with bipolar output buffer. Its published 20 Hz to 20 kHz frequency range, 15 dBA equivalent noise level, and 100-ohm output impedance support clean capture with compatible professional equipment. The microphone has a smooth, balanced character intended for critical recording rather than built-in tonal coloration.\u003c\/p\u003e\u003cp\u003eA three-position pad provides 0 dB, -10 dB, and -20 dB attenuation for adapting to louder sources. The selectable high-pass filter offers flat response, 75 Hz, or 150 Hz settings, with 12 dB-per-octave filtering at the two cutoff positions. These controls help manage excessive level, low-frequency rumble, handling noise, and proximity-related low end before the signal reaches the preamp.\u003c\/p\u003e\u003cp\u003eThe NT55 can be the primary close microphone for acoustic instruments or part of a larger recording setup with additional microphones and channels. Its interchangeable capsule design lets users change directionality without changing the microphone body, which can simplify a compact mic locker. For stereo recording, RØDE also offers the model as an acoustically matched pair configuration.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eInterchangeable Capsules:\u003c\/strong\u003e Includes cardioid and omnidirectional options for flexible pickup coverage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.5-Inch True Condenser:\u003c\/strong\u003e Externally biased, gold-sputtered capsule supports detailed instrument recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Position Pad:\u003c\/strong\u003e Select 0, -10, or -20 dB attenuation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-Pass Filter:\u003c\/strong\u003e Flat, 75 Hz, and 150 Hz settings reduce low-frequency buildup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-Noise Electronics:\u003c\/strong\u003e JFET impedance converter and bipolar output buffer support clean signal transfer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced XLR Output:\u003c\/strong\u003e Connects to P48-equipped microphone preamps, mixers, and interfaces.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT55 has a compact 145 mm by 20 mm body with a heavy-duty satin nickel-plated finish. Its small-diaphragm format is practical for close placement around instruments and other space-limited recording positions. The supplied components include an NT45-O omnidirectional capsule, RM5 mic clip, WS5 windshield, and ZP1 zip pouch.\u003c\/p\u003e\u003cp\u003eConnect the NT55 with a standard 3-pin XLR microphone cable to a compatible interface, mixer, recorder, or preamp that provides P48 phantom power. Turn phantom power off and disconnect the XLR cable before changing capsules, then screw the selected capsule onto the microphone body. Use the pad for high-level sources and select the high-pass filter when low-frequency rumble or unwanted bass buildup is present.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668878549062,"sku":"NT55","price":389.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/41cNpH2jdbL.jpg?v=1784468593"},{"product_id":"rode-nt55mp-matched-pair-condenser-microphones","title":"RØDE NT55MP Matched Pair Condenser Microphones","description":"\u003cp\u003eThe RØDE NT55MP is a matched pair of small-diaphragm condenser microphones for stereo recording, detailed instrument capture, and applications where a compact microphone placement is useful. Each microphone is supplied with a cardioid capsule installed and an interchangeable omnidirectional capsule for a different pickup pattern. The matched-pair configuration is intended for users building stereo microphone setups for music, ambience, broadcast, and location work.\u003c\/p\u003e\u003cp\u003eIts 1\/2-inch gold-sputtered true condenser capsule is designed to provide a smooth, balanced recording character across a 20Hz to 20kHz frequency range. The NT55's low 15dBA equivalent noise level supports recording quieter sources with less microphone self-noise. A 100-ohm balanced XLR output lets it integrate with professional microphone preamps, mixers, recorders, and interfaces.\u003c\/p\u003e\u003cp\u003eThe NT55MP provides practical control for sources with different volume levels and low-frequency conditions. Its three-position pad offers 0dB, -10dB, and -20dB settings, while the high-pass filter can be set flat, at 75Hz, or at 150Hz. These controls help accommodate louder instruments and reduce unwanted low-frequency energy before the signal reaches the preamp.\u003c\/p\u003e\u003cp\u003eInterchangeable NT45-C cardioid and NT45-O omnidirectional capsules make the pair adaptable to different recording techniques. Cardioid operation is useful when greater focus on the intended source is needed, while the omni capsules offer an alternate pickup option. The microphones use JFET impedance converters with bipolar output buffers and require P48 phantom power.\u003c\/p\u003e\u003cp\u003eAs part of a recording system, the NT55MP connects to two balanced XLR microphone inputs with phantom power available on both channels. It is suited to stereo techniques, paired spot-miking, drum overhead use, acoustic instruments, dialogue, and environmental recording. The included clips, windscreens, omni capsules, and zip pouch provide the essential accessories for storage and deployment.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAcoustically Matched Pair:\u003c\/strong\u003e Two NT55 microphones support consistent stereo recording setups.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInterchangeable Capsules:\u003c\/strong\u003e Includes cardioid and omnidirectional pickup pattern options.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Position Pad:\u003c\/strong\u003e Select 0dB, -10dB, or -20dB attenuation for louder sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable High-Pass Filter:\u003c\/strong\u003e Flat, 75Hz, and 150Hz settings help manage low frequencies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e A 15dBA equivalent noise rating supports detailed capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced XLR Output:\u003c\/strong\u003e Connects directly to professional mic preamps and mixers.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eEach NT55 uses a 1\/2-inch externally biased, gold-sputtered condenser capsule and a heavy-duty satin nickel-plated body. The compact microphone body measures 145 x 20 x 20mm and weighs 100g. Its end-address design, switchable pad, and high-pass filter place useful controls directly on the microphone body.\u003c\/p\u003e\u003cp\u003eConnect each microphone to a balanced XLR input on a mixer, audio interface, recorder, or microphone preamp that provides P48 phantom power. Use the supplied RM5 clips to mount the microphones on compatible stands or booms, then select the cardioid or omnidirectional capsule before powering the microphones. Disconnect the XLR cable before changing capsules, and use the included windscreens and zip pouch for protection during transport and storage.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668878581830,"sku":"NT55MP","price":841.91,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71uCt43yn9L.jpg?v=1784468633"},{"product_id":"rode-nt6-compact-condenser-microphone-with-remote-capsule","title":"Rode NT6 Compact Condenser Microphone with Remote Capsule","description":"\u003cp\u003eThe Rode NT6 is a compact small-diaphragm condenser microphone designed for close, discreet, and difficult-to-reach microphone placement. Its remote capsule separates the recording head from the preamp body, helping users position the capsule where a conventional microphone body may not fit. It is suited to instrument recording, location work, broadcast, theatre, live performance, and environmental recording.\u003c\/p\u003e\u003cp\u003eA fixed cardioid pickup pattern focuses capture toward the intended source while reducing pickup from the sides and rear. The NT6 covers a 40Hz to 20kHz frequency range and uses a 1\/2-inch externally biased, gold-sputtered condenser capsule. Its compact capsule supports detailed close-miking without placing a full microphone body directly at the recording position.\u003c\/p\u003e\u003cp\u003eThe capsule connects to the remote preamp body with a 3m shielded, Kevlar-reinforced cable. This split design allows the capsule to remain in a tight or visually unobtrusive location while the preamp controls stay accessible elsewhere. A multi-position mounting ring provides 180 degrees of vertical capsule adjustment for accurate aiming.\u003c\/p\u003e\u003cp\u003eThe preamp body includes a selectable 80Hz high-pass filter and a -10dB pad. The high-pass filter can help reduce low-frequency rumble and vibration when those frequencies are not part of the desired source. The pad adds headroom for louder instruments and sound sources, raising maximum SPL handling to 145dB with the pad enabled.\u003c\/p\u003e\u003cp\u003eThe NT6 uses a balanced 3-pin XLR output and requires 24V or 48V phantom power from a compatible mixer, audio interface, recorder, or microphone preamp. Its RM5 stand mount, WS5 windshield, and padded pouch support practical studio and field deployment. It can serve as a compact standalone microphone or as a focused component within a larger recording setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemote 1\/2-Inch Capsule:\u003c\/strong\u003e Places the recording head in tight or discreet locations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the intended sound source.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e3m Kevlar-Reinforced Cable:\u003c\/strong\u003e Separates the capsule from the remote preamp body.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e80Hz High-Pass Filter:\u003c\/strong\u003e Helps reduce unwanted low-frequency rumble and vibration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e-10dB Pad:\u003c\/strong\u003e Adds headroom when recording louder sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24V Or 48V Phantom Power:\u003c\/strong\u003e Works with compatible professional microphone inputs.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT6 uses an externally biased, gold-sputtered condenser capsule and a heavy-duty satin-nickel plated preamp body. Its surface-mount preamp circuitry is housed separately from the capsule, while the included capsule mounting ring provides two-axis adjustment and 180 degrees of vertical rotation. The capsule assembly supports 1\/4-inch mounting and includes adapters for common microphone stand, tripod, and boompole thread sizes.\u003c\/p\u003e\u003cp\u003eMount the capsule close to the desired source using the swivel mount, then route the supplied 3m cable to the preamp body and secure the body with the included RM5 stand mount as needed. Connect a standard balanced XLR microphone cable from the preamp body to a mixer, recorder, or interface that provides 24V or 48V phantom power. Set the high-pass filter or pad before recording, and ensure miniature cable connectors are aligned correctly before inserting them.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668879597638,"sku":"NT6","price":449.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81imxC74YkL.jpg?v=1784468677"},{"product_id":"rode-ntg3-rf-bias-shotgun-condenser-microphone","title":"Rode NTG3 RF-Bias Shotgun Condenser Microphone","description":"\u003cp\u003eThe Rode NTG3 is a broadcast-grade shotgun condenser microphone for film, television, video production, location recording, and voice-over work. Its tightly controlled supercardioid pickup pattern helps focus on the intended sound source while reducing unwanted ambient sound. It is a practical choice for crews that need a professional XLR microphone for cameras, field recorders, and audio mixers.\u003c\/p\u003e\u003cp\u003eDesigned for demanding outdoor and location work, the NTG3 uses externally RF-biased condenser electronics for strong resistance to moisture and condensation. This helps address reliability concerns that can affect conventional condenser microphones in changing weather and humid environments. The microphone also uses a custom XLR connector designed to reduce susceptibility to radio-frequency interference.\u003c\/p\u003e\u003cp\u003eThe NTG3 delivers a 40 Hz to 20 kHz frequency range, 13 dBA equivalent noise, and a 117 dB dynamic range. Its stated 130 dB maximum SPL handling supports use around dialogue, effects, and louder production environments. Rode describes its sound character as rich and warm, with controlled off-axis response.\u003c\/p\u003e\u003cp\u003eAt 255 mm long and 163 g, the NTG3 is sized for boom, stand, camera, and handheld microphone setups where directional reach is needed without a large microphone body. Its end-address design makes aiming straightforward: point the front of the microphone toward the desired source. The included foam windshield is intended for outdoor use when light wind protection is needed.\u003c\/p\u003e\u003cp\u003eThe NTG3 connects through a balanced 3-pin XLR output and requires 48V phantom power. It can be integrated with professional cameras, audio recorders, mixing consoles, or compatible wireless transmitters that can supply the required power. The package includes an RM5 microphone clip, windshield, padded zip pouch, and a protective aluminum storage cylinder for transport and storage.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRF-Bias Electronics:\u003c\/strong\u003e Helps resist moisture and condensation in demanding recording conditions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Pattern:\u003c\/strong\u003e Focuses pickup toward the subject while reducing surrounding sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 13 dBA equivalent noise supports clean source capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBalanced XLR Output:\u003c\/strong\u003e Connects to professional cameras, mixers, and recorders.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e48V Phantom Power:\u003c\/strong\u003e Uses standard P48 power from compatible professional equipment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Protective Accessories:\u003c\/strong\u003e Includes windshield, clip, pouch, and storage cylinder.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NTG3 has a slim 19 mm diameter body with a satin-nickel finish for the silver version. It uses a line-gradient acoustic design, a 0.50-inch capsule, and end-address orientation. The included aluminum storage cylinder is water-resistant and designed to protect the microphone during storage and travel.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a balanced XLR input that supplies 48V phantom power at a minimum of 5 mA. Mount it with the included RM5 clip or a compatible shock mount, taking care not to block the slots along the microphone body because doing so can affect its sound and directional pattern. Use the included windshield outdoors, and consider a more specialized windshield or suspension system for stronger wind or handling-noise control.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668880482374,"sku":"NTG3","price":559.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/41FUUR3QoCL.jpg?v=1784468817"},{"product_id":"rode-ntk-large-diaphragm-tube-condenser-microphone","title":"RØDE NTK Large-Diaphragm Tube Condenser Microphone","description":"\u003cp\u003eThe RØDE NTK is a large-diaphragm valve condenser microphone for studio recording applications that call for detailed capture and a controlled cardioid pickup pattern. It is designed for recording sources such as vocals, acoustic instruments, piano, guitar amplifiers, and drum overheads. Its dedicated external power supply supports the tube-based microphone circuitry.\u003c\/p\u003e\u003cp\u003eA 1-inch gold-sputtered condenser capsule and hand-selected 6922 twin-triode valve are at the center of the NTK design. This combination is intended to deliver a warm, full recording character while retaining detail across its 20Hz to 20kHz frequency range. The fixed cardioid pattern helps focus pickup toward the intended source while reducing sound arriving from behind the microphone.\u003c\/p\u003e\u003cp\u003eThe NTK is suited to creators, musicians, engineers, and studios building an XLR-based recording chain. Its 25mV\/Pa sensitivity and low 12dBA equivalent noise level support capture of nuanced vocal and instrument performances. With a maximum SPL rating above 158dB, it can also accommodate high-level sound sources when positioned and gain-staged appropriately.\u003c\/p\u003e\u003cp\u003eClass-A valve circuitry uses a valve\/tube impedance converter with a bipolar output buffer. The microphone connects to its dedicated power supply through a 7-pin cable, while the power supply feeds a mixer or microphone preamplifier through XLR. This separates the microphone from mains power hardware and provides a practical interface for conventional studio equipment.\u003c\/p\u003e\u003cp\u003eThe NTK can serve as a primary vocal microphone or as a character-focused option alongside other studio condensers. Its included external power supply integrates with a mixer, preamp, or audio interface that accepts an XLR microphone signal. For vocal work, a pop filter and stable stand setup help manage plosives, moisture, and placement consistency.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Gold-Sputtered Capsule:\u003c\/strong\u003e Provides a large-diaphragm condenser platform for detailed recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6922 Twin-Triode Valve:\u003c\/strong\u003e Uses a hand-selected tube in the microphone circuit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the front of the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e Rated at 12dBA equivalent noise for quieter sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Handles sound-pressure levels above 158dB SPL.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDedicated Power Supply:\u003c\/strong\u003e Powers the valve circuitry and provides XLR output.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NTK uses a side-address body with a high-strength, heat-treated steel mesh head. Its internal design combines a pressure-gradient condenser capsule, Class-A valve circuitry, and a hand-selected 6922 tube. The microphone measures 208 x 55 x 55mm and has a net weight of 760g.\u003c\/p\u003e\u003cp\u003eConnect the microphone to the dedicated power supply with the supplied 7-pin microphone cable before connecting the power supply to mains power. Run an XLR microphone cable from the power supply output to a mixer, preamplifier, or audio interface, and secure the microphone on a stable stand using the supplied mount or shock mount. Position the gold dot toward the source, and use a pop filter for vocal recording; do not disconnect the microphone cable while the system is powered.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668881694790,"sku":"NTK","price":619.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/6108nO_65IL.jpg?v=1784468999"},{"product_id":"rode-nt-usb-professional-usb-condenser-microphone","title":"RØDE NT-USB+ Professional USB Condenser Microphone","description":"\u003cp\u003eThe RØDE NT-USB+ is a USB condenser microphone designed to capture clear voice, vocal, and instrument recordings directly to a computer, tablet, or compatible smartphone. It provides a streamlined alternative to a separate XLR microphone, audio interface, and preamp setup. Its class-compliant USB connection supports straightforward plug-and-play use for recording, streaming, calls, and content creation.\u003c\/p\u003e\u003cp\u003eThis microphone is suited to podcasters, musicians, streamers, voice-over creators, and remote workers who want a dedicated desktop microphone. Its cardioid pickup pattern focuses on sound from the front of the microphone while helping reduce pickup from behind it. The included pop filter helps reduce plosive bursts when recording speech and vocals.\u003c\/p\u003e\u003cp\u003eThe NT-USB+ uses a studio-grade condenser capsule with a pressure-gradient acoustic design and an ultra-low-noise Revolution Preamp. It supports 24-bit, 48 kHz digital audio over USB-C for detailed recordings without requiring an external audio interface. With a 20 Hz to 20 kHz frequency range and 118 dB maximum input SPL at 10% THD, it can be used for spoken word, singing, and instruments.\u003c\/p\u003e\u003cp\u003eA built-in 3.5 mm headphone output supports direct, zero-latency monitoring while recording or streaming. Dedicated headphone level and monitor-mix controls allow the user to balance microphone monitoring with audio coming from the connected device. This makes it easier to hear performance and playback without the delayed monitoring that can occur through software.\u003c\/p\u003e\u003cp\u003eFor users who want additional voice shaping, the NT-USB+ supports onboard processing configured through compatible RØDE software. Available processing includes a noise gate, compressor, high-pass filter settings, and APHEX Aural Exciter and Big Bottom processing. The included desktop tripod, ring mount, pop filter, and USB-C cable provide a complete starting setup, while the ring mount can also attach to compatible tripods or studio arms.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Condenser Capsule:\u003c\/strong\u003e Focuses pickup toward the speaker or performer in front of the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRevolution Preamp:\u003c\/strong\u003e Provides high-gain microphone amplification with a low-noise design.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24-Bit \/ 48 kHz Audio:\u003c\/strong\u003e Delivers high-resolution digital recording through its USB-C connection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eZero-Latency Monitoring:\u003c\/strong\u003e Lets you monitor the microphone directly through connected headphones.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOnboard DSP Processing:\u003c\/strong\u003e Supports configurable compression, noise gate, filtering, and APHEX processing.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDesktop Recording Kit:\u003c\/strong\u003e Includes a tripod, ring mount, pop filter, and USB-C cable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NT-USB+ has a compact desktop-oriented design with a 184 mm length, 62 mm width, and 50 mm depth. Its ring mount holds the microphone in position and includes a removable 1\/4-inch to 5\/8-inch thread adapter for use with compatible mounting hardware. A front-facing gold dot identifies the front of the cardioid capsule for correct placement.\u003c\/p\u003e\u003cp\u003eConnect the included SC29 USB-C to USB-C cable between the microphone and a USB-C-equipped computer, tablet, or smartphone. A computer with only USB-A ports requires a compatible USB-C-to-USB-A cable, while Lightning-equipped iPhone and iPad models require a compatible Lightning accessory cable. Attach the supplied pop filter for speech or vocal recording, connect headphones to the 3.5 mm output when monitoring is needed, and select NT-USB+ as the input and output device in the recording or communication app.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668882186310,"sku":"NTUSB+","price":157.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51Qshd1JNaL.jpg?v=1784469333"},{"product_id":"rode-tf5mp-precision-matched-condenser-microphone-pair","title":"RØDE TF5MP Precision-Matched Condenser Microphone Pair","description":"\u003cp\u003eThe RØDE TF5MP is a precision-matched pair of small-diaphragm cardioid condenser microphones built for detailed stereo music recording. It is designed for engineers and musicians who need consistent capture across two microphone channels for ensemble, orchestral, piano, drum, and acoustic-instrument sessions. The included Stereo Bar helps place the microphones as a coordinated stereo array.\u003c\/p\u003e\u003cp\u003eEach TF-5 uses an externally biased condenser design with a JFET impedance converter and bipolar output buffer. Its cardioid pickup pattern focuses on sound arriving from the front while helping reduce pickup from the rear. The microphones combine a specified 20 Hz to 20 kHz frequency response with a low 14 dB SPL equivalent-noise rating.\u003c\/p\u003e\u003cp\u003eThe TF-5 pair is suited to sources where transient detail, tonal consistency, and stereo imaging matter. A 135 dB SPL rating at 1% THD supports use on louder acoustic sources as well as more delicate performances. With 35 mV\/Pa sensitivity, the microphones are designed to capture subtle musical detail when used with suitable preamps.\u003c\/p\u003e\u003cp\u003eRØDE precision-matches the pair for consistent tone and response between the two microphones. The capsule design is engineered to sub-micron tolerances, supporting the close matching needed for stereo techniques. The result is a practical matched-pair format for critical recording work rather than two unrelated individual microphones.\u003c\/p\u003e\u003cp\u003eThis TF5MP package provides the core components needed to build a stereo microphone setup, including a Stereo Bar, two mic clips, two windshields, and a 3\/8-inch to 5\/8-inch adaptor. It works as part of a recording system with two microphone inputs and 48V phantom power. The microphones may also be separated for individual spot-miking duties when a matched stereo setup is not required.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrecision-Matched Pair:\u003c\/strong\u003e Two TF-5 microphones are selected for closely matched stereo recording performance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses capture toward the front of each microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Equivalent Noise:\u003c\/strong\u003e 14 dB SPL self-noise supports quiet-source recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Handles up to 135 dB SPL at 1% THD.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eJFET Output Stage:\u003c\/strong\u003e Uses a JFET impedance converter with bipolar output buffer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Stereo Kit:\u003c\/strong\u003e Includes Stereo Bar, clips, windshields, and thread adaptor.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe TF-5 has a compact pencil-style small-diaphragm design measuring 98.7 mm long by 20 mm in diameter. Each microphone weighs 114 g, making the pair manageable for stereo bars, stands, and other appropriate microphone mounting hardware. Its externally biased condenser capsule and active electronics are engineered for consistent recording performance.\u003c\/p\u003e\u003cp\u003eMount the two included microphones in the supplied Stereo Bar using the included mic clips, then attach the bar to a compatible stand with the supplied 3\/8-inch to 5\/8-inch adaptor as needed. Connect each microphone to a separate microphone input that can provide 48V phantom power, with a specified draw of 7 mA per microphone. Use the included windshields when light air movement or close positioning makes them useful, and adjust microphone spacing and angle for the desired stereo technique.\u003c\/p\u003e","brand":"Rode","offers":[{"title":"Default Title","offer_id":45668889788486,"sku":"TF5MP","price":1449.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/612dYJpJA7L.jpg?v=1784469806"},{"product_id":"shure-beta87a-supercardioid-condenser-vocal-microphone","title":"Shure BETA87A Supercardioid Condenser Vocal Microphone","description":"\u003cp\u003eThe Shure BETA87A is a wired handheld electret condenser microphone designed for lead and background vocals. Its supercardioid pickup pattern focuses on the performer while helping reduce unwanted off-axis sound. It is suited to live sound reinforcement and studio recording applications.\u003c\/p\u003e\u003cp\u003eA smooth 50 Hz to 20 kHz frequency response with a gradual presence rise is tailored for clear vocal reproduction. The microphone also uses a controlled low-frequency roll-off to help manage proximity effect during close vocal work. This makes it practical for singers who work close to the grille on stage or in recording setups.\u003c\/p\u003e\u003cp\u003eThe BETA87A handles high sound-pressure levels, with a maximum SPL rating of 140.5 dB under Shure's specified test conditions. Its 117 dB dynamic range and low self-noise support detailed vocal capture across quiet passages and louder performances. The balanced XLR output is intended for professional mixers, interfaces, and microphone preamps.\u003c\/p\u003e\u003cp\u003eAn advanced cartridge shock-mount system helps reduce mechanical shock and handling noise. The integrated pop filter helps limit wind and breath noise without requiring an external filter for routine vocal use. Its supercardioid pattern can also help increase usable gain before feedback when loudspeakers are placed appropriately.\u003c\/p\u003e\u003cp\u003eThe microphone requires 11 to 52 V DC phantom power and performs best with a 48 V DC supply. It connects through a balanced XLR-to-XLR or XLR-to-TRS microphone cable, depending on the input equipment. An A25D microphone clip and zippered carrying bag are included for stand mounting, storage, and transport.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eElectret Condenser Capsule:\u003c\/strong\u003e Captures vocal detail with a wide 50 Hz to 20 kHz response.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Pattern:\u003c\/strong\u003e Focuses pickup toward the vocalist and rejects much off-axis sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControlled Low-Frequency Roll-Off:\u003c\/strong\u003e Helps manage proximity effect during close microphone technique.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Capability:\u003c\/strong\u003e Handles up to 140.5 dB SPL under specified conditions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Pop Filter:\u003c\/strong\u003e Reduces unwanted breath and wind noise during vocal use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShock-Mounted Cartridge:\u003c\/strong\u003e Helps minimize handling noise and mechanical vibration.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe BETA87A uses an aluminum housing with a painted blue metallic finish. Its hardened steel grille has nickel satin chrome plating, and the microphone has a net weight of 0.207 kg (0.475 lb). The design combines a handheld vocal form factor with an internal cartridge shock mount and built-in pop filter.\u003c\/p\u003e\u003cp\u003eConnect the microphone's male three-pin balanced XLR output to a compatible balanced microphone input using an XLR-to-XLR or XLR-to-TRS cable. Enable phantom power from 11 to 52 V DC, with 48 V DC preferred for full specified performance. For stage use, mount it in the included A25D clip and place monitor speakers toward the microphone's rear 120-degree rejection points rather than directly behind it.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668939595846,"sku":"BETA87A","price":260.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61Kh4GCIrPL.jpg?v=1784471329"},{"product_id":"shure-beta87c-cardioid-condenser-vocal-microphone","title":"Shure BETA87C Cardioid Condenser Vocal Microphone","description":"\u003cp\u003eThe Shure BETA87C is a handheld electret condenser vocal microphone designed for stage performance, live recording, and studio vocal work. Its cardioid pickup pattern focuses on the performer while helping reduce sound entering from the rear and sides. It is suited to singers who need a wired vocal microphone with phantom-powered condenser operation.\u003c\/p\u003e\u003cp\u003eThe BETA87C has a smooth vocal response with a slight presence rise, intended to retain clarity while supporting a warm, natural overall character. Its controlled low-frequency roll-off helps manage proximity effect during close vocal use. This makes it practical for performers who work close to the microphone for isolation and monitoring.\u003c\/p\u003e\u003cp\u003eA uniform cardioid pattern provides consistent pickup behavior and minimal off-axis tonal coloration. Positioning unwanted sound sources, including stage monitors, behind the microphone supports its rear rejection characteristics. The pattern is particularly useful for vocalists using personal in-ear monitoring systems.\u003c\/p\u003e\u003cp\u003eThe microphone combines an advanced cartridge shock-mount system with a built-in three-stage pop filter. These features help reduce handling-related mechanical noise as well as breath and wind noise during close singing. Its hardened steel-mesh grille and metal housing are designed for regular touring and sound-reinforcement use.\u003c\/p\u003e\u003cp\u003eThe BETA87C connects through a balanced three-pin XLR output and requires phantom power from a compatible mixer, interface, preamp, or external phantom-power supply. It performs best with a 48 V DC phantom-power source and can operate from 11 to 52 V DC. The included swivel adapter and carrying bag provide the basics needed to mount, transport, and store the microphone.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the vocalist while providing rear rejection of unwanted sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElectret Condenser Capsule:\u003c\/strong\u003e Delivers phantom-powered condenser performance for vocal applications.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Stage Pop Filter:\u003c\/strong\u003e Helps reduce breath pops and wind noise during close use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eControlled Proximity Response:\u003c\/strong\u003e Low-frequency roll-off helps manage excessive bass buildup near the grille.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eInternal Shock Mount:\u003c\/strong\u003e Helps minimize handling noise and mechanical vibration reaching the cartridge.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHardened Steel Grille:\u003c\/strong\u003e Provides durable protection for regular stage and touring use.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe BETA87C uses an aluminum body with a painted blue metallic finish and a hardened steel grille with nickel satin chrome plating. Its internal cartridge shock mount is intended to reduce mechanical vibration, while the dent-resistant grille protects the capsule area. The microphone measures 192 mm long, with a 51 mm grille diameter and a 21 mm body diameter.\u003c\/p\u003e\u003cp\u003eConnect the male XLR output to a balanced XLR microphone cable and a mixer, preamp, audio interface, or phantom-power supply that provides 11 to 52 V DC phantom power; 48 V DC is preferred. Mount it with the included A25D swivel adapter on a compatible microphone stand, and aim the rear of the cardioid microphone toward unwanted sound sources or monitors. For outdoor use, Shure recommends adding a windscreen.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668939923526,"sku":"BETA87C","price":260.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51oCK9Q4XYL.jpg?v=1784471369"},{"product_id":"shure-ksm32c-hm-cardioid-condenser-microphone","title":"Shure KSM32C\/HM ¾\" Cardioid Condenser Microphone","description":"\u003cp\u003eThe Shure KSM32C\/HM is a cardioid condenser microphone stage kit designed for detailed vocal, instrument, overhead, and ensemble recording. Its focused pickup pattern helps reduce unwanted room sound and nearby-source bleed when recording in less-than-perfect acoustic spaces. The included hard mount, windscreen, carrying case, and threaded adapter make it a practical package for studio and stage-oriented setups.\u003c\/p\u003e\u003cp\u003eBuilt around a Shure-designed ¾-inch embossed Mylar diaphragm capsule, the KSM32C is voiced for a smooth and even response rather than pronounced tonal emphasis. It delivers extended low-frequency performance associated with larger capsules while retaining a compact physical format. This makes it suited to sources where natural tone, transient detail, and controlled placement matter.\u003c\/p\u003e\u003cp\u003eThe cardioid pattern provides up to 37 dB of rear rejection at 180 degrees, helping keep reflections and surrounding instruments out of the microphone signal. With an 11 dBA typical self-noise specification and 83 dB signal-to-noise ratio, it is equipped for recording quieter and more detailed material. Its neutral response also gives engineers a flexible starting point for later EQ and dynamics processing.\u003c\/p\u003e\u003cp\u003eA selectable 15 dB pad expands the microphone's ability to work with high-SPL sources such as drums, guitar amplifiers, horns, and percussion. The three-position low-frequency filter provides flat response, a 115 Hz rolloff, or an 80 Hz cutoff to help manage proximity effect, vibration, and low-frequency buildup. These controls allow the microphone to adapt to different sources without adding external inline attenuation.\u003c\/p\u003e\u003cp\u003eThe KSM32C\/HM connects through a balanced three-pin XLR output and requires standard 48 V phantom power. Its lightweight machined anodized aluminum housing is intended for dependable placement on boom stands and mic stands. It is a useful upgrade for creators and engineers who need a dedicated large-diaphragm-style condenser sound with controlled off-axis behavior in a compact microphone.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e¾-Inch Electret Capsule:\u003c\/strong\u003e Embossed Mylar diaphragm supports smooth, detailed capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the source and reduces rearward sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 11 dBA typical self-noise supports detailed recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 dB Pad:\u003c\/strong\u003e Handles louder sources with increased headroom.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Position Low Cut:\u003c\/strong\u003e Helps manage rumble, vibration, and proximity effect.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStage Kit Accessories:\u003c\/strong\u003e Includes hard mount, windscreen, case, and adapter.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe KSM32C uses a machined, anodized aluminum-alloy housing with a precision-machined steel grille. Its compact all-metal construction is lightweight at 265 g while providing a durable format for studio and live-sound use. The capsule uses a gold-layered design behind the grille, and the microphone body includes accessible pad and frequency-response switches.\u003c\/p\u003e\u003cp\u003eConnect the microphone's male XLR output to a balanced XLR microphone input on a mixer, audio interface, or preamp that supplies 48 V phantom power. Mount it with the included swivel-mount mic clamp, then use the flat setting for full-range capture or select one of the low-frequency filters when controlling rumble or proximity effect is useful. The included flocked foam windscreen can help reduce light wind and breath noise, while the zippered case supports protected transport and storage.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668958830662,"sku":"KSM32C\/HM","price":659.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61ux4-CWNCL.jpg?v=1784474441"},{"product_id":"shure-ksm32c-sm-cardioid-condenser-microphone-studio-kit","title":"Shure KSM32C\/SM Cardioid Condenser Microphone Studio Kit","description":"\u003cp\u003eThe Shure KSM32C\/SM is a studio kit built around the KSM32C cardioid condenser microphone. It is designed for detailed, neutral capture of vocals, acoustic instruments, drum overheads, ensembles, guitar amplifiers, and other sources where a controlled recording is important. Its cardioid pickup pattern helps focus on the intended source while reducing pickup from the rear and sides.\u003c\/p\u003e\u003cp\u003eThis microphone suits home studios, professional tracking rooms, content creators, and live-sound users who need a versatile condenser with a compact side-address form factor. The KSM32C uses a ¾-inch single-diaphragm electret capsule rather than a conventional 1-inch large-diaphragm design. Shure engineered the capsule for a smooth, extended response with strong low-frequency performance.\u003c\/p\u003e\u003cp\u003eThe KSM32C is voiced for transparent, even reproduction rather than pronounced high-frequency emphasis. Its 20 Hz to 20 kHz frequency response and 11 dBA typical self-noise support clean capture of both quiet and high-output sources. A cardioid polar pattern and specified rear rejection help reduce room reflections and nearby instruments in multi-source sessions.\u003c\/p\u003e\u003cp\u003eFor louder sources, the microphone includes a selectable 15 dB attenuation pad and handles up to 155 dB SPL at 1% THD with the pad engaged into 2,500 or 5,000 ohm loads. A three-position low-frequency filter provides flat response, a 115 Hz low-frequency rolloff, or an 80 Hz low-frequency cutoff. These controls help manage proximity effect, rumble, and excessive low-end energy at the microphone.\u003c\/p\u003e\u003cp\u003eThe KSM32C\/SM Studio Kit provides the accessories needed to position and protect the microphone in a recording setup. It includes a dedicated shock mount, magnetic pop filter, premium zippered carrying case, replacement shock-mount bands, and a threaded adapter. Connect it to a balanced XLR microphone input with 48 V phantom power, then pair it with a suitable preamp, audio interface, mixer, or console.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e¾-Inch Electret Capsule:\u003c\/strong\u003e Embossed Mylar diaphragm supports smooth, extended capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Helps focus pickup on the source in front.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 11 dBA typical self-noise supports detailed recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable 15 dB Pad:\u003c\/strong\u003e Accommodates high-SPL instruments and amplifiers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Position Low-Cut Filter:\u003c\/strong\u003e Helps manage rumble and excessive low frequencies.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Studio Kit:\u003c\/strong\u003e Includes shock mount, pop filter, case, bands, and adapter.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe KSM32C uses a machined, anodized aluminum-alloy housing with a precision-machined steel grille. Its compact body measures 47.6 x 154.2 mm and weighs 265 g, making it practical for placement on boom stands. The studio kit's shock mount is intended to isolate the microphone from stand-borne vibration, while the magnetic pop filter helps reduce vocal plosives.\u003c\/p\u003e\u003cp\u003eUse a balanced three-pin XLR microphone cable and a preamp, mixer, or audio interface that supplies standard 48 V phantom power. Position the Shure logo toward the sound source, and use the supplied shock mount for studio placement. Start with the pad off for normal sources, engage the pad for very loud sources, and select a low-frequency filter when rumble, proximity effect, or low-end buildup needs to be reduced.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668958994502,"sku":"KSM32C\/SM","price":729.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61ux4-CWNCL_1f5964a0-2a8b-462f-bbbf-14841f984a8c.jpg?v=1784474478"},{"product_id":"shure-ksm40c-1-cardioid-condenser-microphone","title":"Shure KSM40C 1\" Cardioid Condenser Microphone","description":"\u003cp\u003eThe Shure KSM40C is a large-diaphragm, side-address condenser microphone designed for detailed studio recording. Its cardioid pickup pattern helps focus on the intended source while reducing surrounding room sound and bleed. It is suited to vocal recording, voiceover, acoustic instruments, guitar amplifiers, upright bass, and kick drum applications.\u003c\/p\u003e\u003cp\u003eA precision-engineered 1-inch single-diaphragm capsule gives the KSM40C a full low-frequency character with smooth high-frequency detail. Its response is designed to capture vocal presence and instrument nuance without emphasizing sharp upper-frequency resonances. The uniform cardioid pattern also provides a predictable starting point when positioning the microphone.\u003c\/p\u003e\u003cp\u003eWith 7.5 dBA self-noise and an 86.5 dB signal-to-noise ratio, the KSM40C is equipped for quiet sources and detailed recording work. Its sensitivity of -33.5 dBV\/Pa helps it produce a healthy output for compatible microphone preamps. A selectable 15 dB pad increases headroom for loud sources such as drums, horns, and guitar cabinets.\u003c\/p\u003e\u003cp\u003eThe microphone includes a three-position low-frequency filter for adapting to the recording environment and source placement. Choose flat response for a natural capture, a 115 Hz rolloff to help manage proximity effect, or an 80 Hz high-pass cutoff to reduce low-frequency room noise. These controls make it easier to tailor the microphone before processing.\u003c\/p\u003e\u003cp\u003eThe KSM40C is supplied as a complete studio-ready package with a shock mount, magnetic pop filter, swivel hard mount, carrying case, replacement shock-mount bands, and threaded adapter. It connects through a balanced 3-pin XLR output and requires phantom power from a mixer, audio interface, or dedicated microphone preamp. This makes it a practical upgrade for a recording chain built around a quality XLR input and 48 V phantom power.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Capsule:\u003c\/strong\u003e Large single-diaphragm design captures detailed sound with substantial low-end response.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup:\u003c\/strong\u003e Focuses on the sound source while helping reduce room and off-axis bleed.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e 7.5 dBA self-noise supports clean recording of quieter performances.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 dB Pad:\u003c\/strong\u003e Adds headroom for louder instruments, amplifiers, horns, and drums.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Position Low Cut:\u003c\/strong\u003e Provides flat, 115 Hz rolloff, and 80 Hz cutoff settings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Accessory Suite:\u003c\/strong\u003e Includes shock mount, magnetic pop filter, case, hard mount, bands, and adapter.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe KSM40C uses a machined, anodized aluminum-alloy housing for a durable but relatively lightweight microphone body. Its precision-machined steel grille protects the gold-layered capsule, while the included shock mount helps isolate the microphone from stand-borne vibration. The magnetic pop filter attaches to the shock mount to help reduce plosive sounds during close vocal recording.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a balanced XLR microphone input with phantom power enabled; 48 V DC is specified for full performance. Shure recommends a preamp input impedance of at least 1,000 ohms. Mount it on a stable boom stand using the supplied shock mount or swivel hard mount, then select the pad and low-frequency filter appropriate for the source and placement.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668960305222,"sku":"KSM40C","price":879.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71iMCbgTcCL.jpg?v=1784474520"},{"product_id":"shure-ksm44mp-large-diaphragm-multi-pattern-condenser-microphone","title":"Shure KSM44MP Large-Diaphragm Multi-Pattern Condenser Microphone","description":"\u003cp\u003eThe Shure KSM44MP is a large-diaphragm, side-address condenser microphone designed for detailed studio recording. Its selectable cardioid, omnidirectional, and bidirectional polar patterns let one microphone cover close vocals, instruments, room capture, and stereo techniques. It is suited to creators, engineers, musicians, and studios that need flexible capture options without changing microphones between sources.\u003c\/p\u003e\u003cp\u003eA 1-inch dual gold-layered Mylar diaphragm design delivers a broad 20 Hz to 20 kHz frequency response with a flat character and subtle high-frequency emphasis. The microphone is designed to preserve low-level detail while maintaining very low self-noise, which is useful for quiet vocals, acoustic instruments, ambience, and distant miking. Its pattern options also allow the user to tailor pickup and off-axis rejection to the recording environment.\u003c\/p\u003e\u003cp\u003eThe KSM44MP provides cardioid, omnidirectional, and bidirectional operation from its dual-diaphragm capsule assembly. Cardioid focuses on the source in front of the microphone, omnidirectional captures sound from around it, and bidirectional captures front and rear while rejecting the sides. This makes the microphone practical for solo performances, ensembles, room sound, and stereo configurations such as mid-side or Blumlein setups.\u003c\/p\u003e\u003cp\u003eOn-microphone controls include a 15 dB attenuation pad and a three-position low-frequency response switch. The pad helps manage loud sources such as drums, horns, and guitar cabinets, while the low-cut and low-rolloff settings can reduce room rumble, mechanical noise, wind noise, or proximity effect. A high maximum SPL capability gives the microphone useful headroom across a wide range of studio sources.\u003c\/p\u003e\u003cp\u003eThe KSM44MP connects through a balanced 3-pin XLR output and requires phantom power from a compatible microphone preamp, mixer, or audio interface. It includes a shock mount and magnetic pop filter to support cleaner vocal and instrument recording setups. It can serve as a primary studio vocal microphone or as a flexible addition alongside dedicated close, overhead, and room microphones.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Polar Patterns:\u003c\/strong\u003e Choose cardioid, omnidirectional, or bidirectional pickup for different sources and recording techniques.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Dual Diaphragms:\u003c\/strong\u003e Dual gold-layered Mylar diaphragms support multi-pattern operation and consistent response.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow Self-Noise:\u003c\/strong\u003e Captures quiet sources with low background noise from the microphone itself.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 dB Attenuation Pad:\u003c\/strong\u003e Helps prevent overload when recording high-SPL instruments and amplifiers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree-Position Low-Frequency Filter:\u003c\/strong\u003e Provides flat response, low rolloff, or steep low-cut options.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Recording Accessories:\u003c\/strong\u003e Supplied shock mount, magnetic pop filter, hard mount, case, and replacement bands support setup.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe KSM44MP uses a machined, anodized aluminum-alloy housing with a lightweight all-metal construction. Its male XLR connector and internal RF shielding support dependable use in professional recording environments. The microphone measures 47.6 x 171.1 mm and weighs 295 g.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included shock mount or supplied swivel hard mount on a compatible boom or floor stand. Connect it with a balanced XLR microphone cable to a preamp, mixer, or interface that provides phantom power; Shure specifies +48 V DC for best performance and a preamp input impedance of at least 1,000 ohms. Attach the magnetic pop filter to the shock mount for close vocal work, and mute the channel or lower monitoring level before changing the polar-pattern switch.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45668960665670,"sku":"KSM44MP","price":1099.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71Tcm8Wl5DL.jpg?v=1784474560"},{"product_id":"shure-sm4-k-cardioid-condenser-recording-microphone","title":"Shure SM4-K Cardioid Condenser Recording Microphone","description":"\u003cp\u003eThe Shure SM4-K is a side-address cardioid condenser microphone built for home recording, vocal production, streaming, and instrument capture. Its XLR output and externally biased condenser design make it a fit for users working with an audio interface or mixer rather than a USB-only recording setup. The microphone is designed to capture focused sound while reducing pickup from the rear and sides.\u003c\/p\u003e\u003cp\u003eA 1-inch brass dual-diaphragm capsule provides controlled low frequencies and detailed high-frequency reproduction across a 20 Hz to 20 kHz response range. Its broad working area helps reduce excessive proximity effect during close vocal recording. This makes the SM4-K well suited to vocals, speech, acoustic instruments, amplifiers, horns, and drums.\u003c\/p\u003e\u003cp\u003eThe fixed cardioid pattern focuses on the source in front of the microphone and helps reduce unwanted room sound and off-axis distractions. Shure rates the SM4 for a maximum SPL of 140 dB at 1 kHz with 1% THD into a 1 kOhm load, allowing it to handle louder sources without requiring a separate pad setting. A 79 dB signal-to-noise ratio and 15 dB SPL A-weighted self-noise support clean recording work.\u003c\/p\u003e\u003cp\u003eShure's patent-pending Interference Shielding Technology is designed to reduce RF noise from nearby phones, laptops, Wi-Fi routers, and other wireless devices. The design combines an integrated pop filter with a woven mesh Faraday cage around the capsule. This helps keep plosives, interference, and unwanted recording artifacts under control before processing.\u003c\/p\u003e\u003cp\u003eThe SM4-K is the standard microphone package, including a swivel-mount microphone clamp, brass stand adapter, and zippered pouch. It connects through a standard three-pin XLR connection and requires +48 V phantom power from a compatible interface or mixer. Users who need suspension isolation and an external magnetic pop filter can add compatible Shure accessories or choose the separate SM4-K-KIT package.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch Brass Capsule:\u003c\/strong\u003e Dual diaphragms capture controlled lows and detailed highs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the source while reducing off-axis sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Records loud instruments up to 140 dB SPL.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRF Interference Shielding:\u003c\/strong\u003e Helps reduce noise from nearby wireless devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated Pop Filter:\u003c\/strong\u003e Helps control plosives and low-frequency rumble.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eXLR Studio Connection:\u003c\/strong\u003e Works with compatible interfaces and mixers using phantom power.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe SM4-K uses a rugged die-cast zinc housing with all-metal construction and a low-profile black finish. At 463 g, it has the substantial feel of a studio condenser microphone while remaining practical for stand or boom-arm mounting. Its side-address format places the front logo toward the recording source.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included A4M swivel-mount clamp, attach it to a compatible microphone stand, and use the supplied brass adapter when mounting to a 3\/8-inch stand. Connect a three-pin XLR cable to an audio interface or mixer, then enable +48 V phantom power before recording. For vocals, position the source in front of the logo; use a separate external pop filter if additional plosive control is desired.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45669113724998,"sku":"SM4-K","price":219.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51hWkTAKsrL.jpg?v=1784478339"},{"product_id":"shure-sm4-k-kit-studio-condenser-microphone-kit","title":"Shure SM4-K-KIT Studio Condenser Microphone Kit","description":"\u003cp\u003eThe Shure SM4-K-KIT is an XLR condenser microphone package for home recording, streaming, voice work, and instrument capture. It is designed for creators who want a dedicated studio microphone with straightforward analog connectivity rather than a USB-only setup. The kit pairs the SM4 microphone with a shock mount, removable pop filter, stand adapter, and carrying case.\u003c\/p\u003e\u003cp\u003eThe SM4 uses a cardioid pickup pattern to focus on the sound in front of the microphone while reducing unwanted sound from the sides and rear. Its 1-inch dual-diaphragm brass capsule is voiced for controlled low frequencies and detailed high frequencies. This makes it suitable for vocals, acoustic instruments, amplifiers, drums, horns, and other recorded sources.\u003c\/p\u003e\u003cp\u003eFor modern recording spaces, the SM4 incorporates Shure's patent-pending interference shielding technology. Its woven mesh Faraday cage and internal pop filter help reduce radio-frequency interference and vocal plosives before the signal reaches your recording chain. The result is a cleaner starting point for editing, mixing, podcast production, and live-stream content.\u003c\/p\u003e\u003cp\u003eThe microphone handles up to 140 dB SPL with a 1 kΩ load at 1% THD, allowing it to accommodate loud sources such as guitar amplifiers and drums. Its 15 dB SPL typical A-weighted self-noise and 125 dB dynamic range support detailed recording across a wide range of source levels. A broad sweet spot is intended to help provide more consistent close-mic results with reduced proximity effect.\u003c\/p\u003e\u003cp\u003eBecause the SM4 is an analog XLR condenser microphone, it fits naturally into an upgradeable studio system built around an audio interface or mixer. It requires +48 V phantom power and an XLR connection, so it is not a direct USB microphone. The included shock mount and magnetic pop filter make this kit especially practical for vocal recording, desktop studio setups, and camera-facing content creation.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-Diaphragm Capsule:\u003c\/strong\u003e A 1-inch brass capsule captures controlled lows and detailed highs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pattern:\u003c\/strong\u003e Focuses on the intended source while reducing off-axis room noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRF Interference Shielding:\u003c\/strong\u003e Helps block interference from phones, laptops, and Wi-Fi devices.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Handling:\u003c\/strong\u003e Records loud instruments up to 140 dB SPL.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-Stage Pop Filtering:\u003c\/strong\u003e Internal filtering and the removable pop filter reduce plosives.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStudio Kit Accessories:\u003c\/strong\u003e Includes a shock mount, stand adapter, and carrying case.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe SM4 has a rugged die-cast zinc housing with an all-metal exterior designed for regular studio use. Its low-profile side-address form helps keep the microphone visually unobtrusive for video production and streaming. The kit's A4SM shock mount helps damp mechanical vibrations, while the A4PF magnetic pop filter attaches directly to that mount.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included shock mount on a stable microphone stand, then use the supplied brass stand adapter if needed. Connect its male 3-pin XLR output to an audio interface or mixer with an XLR cable, then enable +48 V phantom power. For close vocals, attach the magnetic pop filter; for instruments, adjust placement and input gain to suit the source level.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45669113790534,"sku":"SM4-K-KIT","price":299.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71Cu3CA0yPL.jpg?v=1784478386"},{"product_id":"shure-sm81-lc-cardioid-condenser-instrument-microphone","title":"Shure SM81-LC Cardioid Condenser Instrument Microphone","description":"\u003cp\u003eThe Shure SM81-LC is a cardioid condenser instrument microphone for capturing acoustic instruments in studio, broadcast, and sound-reinforcement setups. Its wide 20 Hz to 20 kHz response and flat-response character are designed for accurate reproduction of the source. It is a practical choice for close or stand-mounted use on acoustic guitar, piano, cymbals, and other detailed sound sources.\u003c\/p\u003e\u003cp\u003eThis microphone uses an electret condenser element and requires external phantom power from a mixer, audio interface, or dedicated microphone preamp. It operates from 11 to 52 V DC phantom power, with 48 V DC providing its intended performance. A balanced XLR microphone cable is required and is not included with the SM81-LC.\u003c\/p\u003e\u003cp\u003eThe cardioid pickup pattern concentrates capture toward the front of the microphone while reducing pickup from the rear and sides. This can help place more attention on the intended instrument in rooms, on stages, or in multi-microphone sessions. Its frequency response is uniform and symmetrical around the microphone axis for controlled off-axis pickup.\u003c\/p\u003e\u003cp\u003eThree selectable low-frequency settings provide useful source and room control without external processing. Choose the flat setting for the most natural response, a 6 dB-per-octave rolloff below 100 Hz to manage proximity effect, or an 18 dB-per-octave cutoff below 80 Hz to reduce rumble and low-frequency room noise. A lockable 0 dB\/-10 dB attenuator helps accommodate louder sources such as drums or guitar cabinets.\u003c\/p\u003e\u003cp\u003eThe SM81-LC is built for regular studio and live production use with a steel body, stainless-steel screens, and a vinyl metallic paint finish. Its low self-noise, high maximum SPL capability, and low RF susceptibility support use across a broad range of acoustic recording and reinforcement tasks. Included mounting and protective accessories make it ready to add to an existing XLR microphone system.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Condenser Capsule:\u003c\/strong\u003e Captures the intended source while reducing surrounding sound pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 Hz to 20 kHz Response:\u003c\/strong\u003e Covers a wide range for detailed instrument capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Low-Frequency Filtering:\u003c\/strong\u003e Helps control rumble, room noise, and proximity effect.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLockable -10 dB Pad:\u003c\/strong\u003e Adds headroom for louder close-miked sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePhantom-Powered Operation:\u003c\/strong\u003e Connects to compatible mixers and interfaces using balanced XLR.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSteel Microphone Housing:\u003c\/strong\u003e Supports dependable use in studio and sound-reinforcement environments.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe SM81-LC has a slim steel housing with a vinyl metallic paint finish and stainless-steel screens. It measures 212 mm long by 23.5 mm in diameter and weighs 230 g. The microphone is supplied with an A57F swivel adapter, 10 dB attenuator lock, foam windscreen, and carrying\/storage bag.\u003c\/p\u003e\u003cp\u003eMount the microphone to a compatible stand or boom with the included swivel adapter, then connect its male three-pin XLR output to a balanced XLR cable. Enable phantom power on the connected mixer, interface, or preamp; the microphone accepts 11 to 52 V DC and performs best from a 48 V DC supply. Select the low-frequency switch and 0 dB or -10 dB attenuator setting for the source, placement, and sound-pressure level.\u003c\/p\u003e","brand":"Shure","offers":[{"title":"Default Title","offer_id":45669117526086,"sku":"SM81-LC","price":439.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51KGL2ldeiL.jpg?v=1784478612"},{"product_id":"presonus-revelator-usb-condenser-microphone","title":"PreSonus REVELATOR USB Condenser Microphone","description":"\u003cp\u003eThe PreSonus REVELATOR is a USB condenser microphone designed for podcasting, streaming, voice-over work, online interviews, and home recording. It combines a microphone, USB audio interface, mixer, onboard effects processor, and headphone amplifier in one desktop-ready unit. This approach helps reduce the need for separate recording hardware for computer-based voice and content-creation setups.\u003c\/p\u003e\u003cp\u003eIts three selectable polar patterns make it suitable for more than one recording situation. Cardioid mode focuses on a single source, omnidirectional mode captures sound around the microphone, and Figure-8 mode is useful for two-person recordings. That flexibility supports solo podcasts, shared interviews, vocals, acoustic instruments, and collaborative sessions.\u003c\/p\u003e\u003cp\u003eThe mono condenser capsule has a 20 Hz to 20 kHz frequency response, 1 mV\/Pa sensitivity, and a maximum SPL rating of 110 dB at less than 3% THD. These specifications support detailed voice and acoustic-instrument capture within its intended desktop recording role. A built-in 1\/8-inch active stereo headphone output provides direct monitoring while recording or streaming.\u003c\/p\u003e\u003cp\u003eRevelator includes onboard Fat Channel processing with a high-pass filter, noise gate, compressor models, EQ models, and limiter. Voice effects include comb filter, delay, doubler, ring modulator, vocoder, and reverb, with eight factory presets and eight user preset locations. Processing settings can be managed from the microphone and through PreSonus Universal Control software.\u003c\/p\u003e\u003cp\u003eFor streaming and remote production, the USB-C-compatible USB 2.0 connection supports integrated computer audio routing and two stereo loopback channels. Multi Mode configures Revelator as three stereo devices: Revelator, Revelator Loopback 1, and Revelator Loopback 2. This makes it practical to combine a microphone with computer playback, calls, game audio, or backing tracks in one desktop recording system.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree Polar Patterns\u003c\/strong\u003e Cardioid, omnidirectional, and Figure-8 modes adapt to solo or shared recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOnboard DSP\u003c\/strong\u003e Fat Channel processing and voice effects shape sound without external hardware.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePreset Storage\u003c\/strong\u003e Eight factory presets and eight user slots support repeatable setups.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLoopback Audio\u003c\/strong\u003e Two stereo loopback channels route computer audio for streams and calls.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeadphone Monitoring\u003c\/strong\u003e The 1\/8-inch output supports direct, zero-latency monitoring.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUSB Bus Power\u003c\/strong\u003e USB-C-compatible USB 2.0 operation does not require a separate power supply.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe REVELATOR uses a black desktop microphone design with a built-in stand and integrated cable management. Its compact enclosure measures 5.13 inches wide by 5.13 inches deep and 8.94 inches high. Front-panel hardware controls provide access to direct monitoring, microphone gain, headphone level, mute, and preset selection.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a compatible computer or supported mobile device through its USB-C-compatible USB 2.0 connection, then select it as the recording and playback device in the desired application. Connect headphones to the 1\/8-inch TRS active stereo output for monitoring, and use Universal Control for advanced routing, polar-pattern selection, monitor mixing, and preset management. For remote interviews or streaming, Multi Mode can separate microphone audio and loopback sources for application-based routing.\u003c\/p\u003e","brand":"PreSonus","offers":[{"title":"Default Title","offer_id":45669200658502,"sku":"REVELATOR","price":129.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81THNU46LbL.jpg?v=1784481384"},{"product_id":"zoom-zpc-1-matched-pencil-condenser-microphone-pair","title":"Zoom ZPC-1 Matched Pencil Condenser Microphone Pair","description":"\u003cp\u003eThe Zoom ZPC-1 is a matched pair of small-diaphragm pencil condenser microphones designed for stereo recording in studio, stage, and field applications. It gives creators a coordinated two-microphone setup for capturing instruments, ensembles, ambience, and other sources with a focused cardioid pickup pattern. The pair is suited to users who need consistent stereo capture without assembling separate microphones.\u003c\/p\u003e\u003cp\u003eEach ZPC-1 uses a back electret condenser design with a 16 mm diaphragm and a 40 Hz to 20 kHz frequency range. Its cardioid pattern emphasizes sound in front of the microphone while reducing pickup from the rear. With a maximum sound pressure level of 134 dB SPL, the microphones can also be positioned near louder acoustic sources when appropriate.\u003c\/p\u003e\u003cp\u003eThe microphones are matched at 1 kHz and 100 Hz to support a consistent stereo result between channels. They can be arranged in an X\/Y configuration for a tighter stereo image with depth or in an A\/B configuration for a wider stereo image. This makes the pair practical for drum overheads, acoustic guitar, ensembles, room capture, and field recording.\u003c\/p\u003e\u003cp\u003eA low equivalent input noise specification of less than 12 dB SPL A-weighted and an 82 dB signal-to-noise ratio support detailed capture of quieter material. The 200-ohm output impedance and XLR-3 connection make the ZPC-1 compatible with professional microphone inputs. Each microphone requires standard +48 V phantom power at 3.5 mA.\u003c\/p\u003e\u003cp\u003eThe ZPC-1 pair fits naturally with a recorder, audio interface, or mixer that has two phantom-powered XLR microphone inputs. Adjustable clips, thread adapters, foam windscreens, and individual carry pouches are included for a ready-to-mount setup. Its compact pencil form factor also makes it convenient to add stereo capability to an existing recording rig.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched Stereo Pair:\u003c\/strong\u003e Two microphones are matched at 1 kHz and 100 Hz for coordinated stereo recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup:\u003c\/strong\u003e Focuses capture toward the source while reducing rear pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBack Electret Condenser:\u003c\/strong\u003e Provides condenser-microphone operation in a compact pencil design.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e134 dB SPL Handling:\u003c\/strong\u003e Supports placement near louder acoustic instruments and sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e+48 V Phantom Power:\u003c\/strong\u003e Works with compatible XLR-equipped mixers, interfaces, and recorders.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Mounting Kit:\u003c\/strong\u003e Includes clips, windscreens, thread adapters, and carry pouches.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eEach ZPC-1 has a solid metal body and measures 20 mm in diameter by 127 mm long. The included adjustable mic clips are made from high-impact plastic, while the foam windscreens use rubber-ringed openings for a snug fit. Two lint-free carrying pouches help keep the microphones and accessories together during transport.\u003c\/p\u003e\u003cp\u003eMount each microphone in an included clip on a compatible 5\/8-inch or 3\/8-inch mic stand, stereo bar, or other suitable mount. Connect each XLR-3 output to a separate microphone input that supplies +48 V phantom power, then use X\/Y placement for a tighter stereo image or A\/B placement for a wider image. Use the included foam windscreens when reducing wind and air noise is helpful.\u003c\/p\u003e","brand":"Zoom","offers":[{"title":"Default Title","offer_id":45669264425030,"sku":"ZPC1","price":169.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51TkkenWWZL.jpg?v=1784487937"},{"product_id":"zoom-ssh-6e-stereo-shotgun-microphone-capsule","title":"Zoom SSH-6e Stereo Shotgun Microphone Capsule","description":"\u003cp\u003eThe Zoom SSH-6e is a Mid-Side stereo shotgun microphone capsule made for focused dialogue and location recording with compatible Zoom Handy Recorders. It combines a highly directional mid microphone with a bidirectional side microphone, helping capture a subject clearly while retaining controlled environmental sound. This approach is useful for video production, interviews, documentary work, and other recordings where direct sound and ambience both matter.\u003c\/p\u003e\u003cp\u003eThe capsule's mid microphone uses a supercardioid polar pattern to focus on sound in front of the recorder. Its side microphone captures the lateral information needed to create a stereo image. By adjusting the recorder's side-mic level, users can set a tighter, more focused image or introduce a wider sense of space.\u003c\/p\u003e\u003cp\u003eFor a straightforward dialogue setup, the side level can be muted so the SSH-6e operates as a mono shotgun microphone. When recording in Raw Mid-Side mode, the stereo width can instead be adjusted later in a DAW with Zoom's MS Decoder software. This gives field recordists flexibility to make stereo decisions during recording or in post-production.\u003c\/p\u003e\u003cp\u003eThe SSH-6e uses Zoom Capsule System 3.0, the connection platform designed for the H6essential, H5studio, and H6studio recorders. With a compatible recorder that supports 32-bit float recording, the system is ready to capture a broad range of sound levels without manual input-gain adjustment. Firmware requirements apply for each compatible recorder model.\u003c\/p\u003e\u003cp\u003eCompact and lightweight, the SSH-6e fits directly onto the compatible recorder's capsule connection rather than requiring a separate cable or external microphone mount. A WSU-2 hairy windscreen is included to help reduce wind interference during outdoor work. It is a practical upgrade for users who need a more focused pickup pattern than a standard stereo capsule while preserving adjustable stereo ambience.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMid-Side Stereo Design:\u003c\/strong\u003e Combines focused direct pickup with adjustable ambient stereo capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Mid Microphone:\u003c\/strong\u003e Concentrates on sound arriving from the front.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBidirectional Side Microphone:\u003c\/strong\u003e Captures side information for an adjustable stereo image.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdjustable Stereo Width:\u003c\/strong\u003e Recorder side-level control changes the apparent width.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRaw Mid-Side Recording:\u003c\/strong\u003e Allows later width adjustment with MS Decoder software.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWSU-2 Windscreen Included:\u003c\/strong\u003e Helps reduce wind noise during outdoor recording.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe SSH-6e is a compact interchangeable microphone capsule measuring 53.2 mm wide, 138.6 mm deep, and 38.1 mm high. It weighs 43 g and uses Zoom's Capsule System 3.0 connection for a stable direct fit on supported recorders. Its two-microphone Mid-Side arrangement places the supercardioid mid mic and bidirectional side mic in one integrated capsule.\u003c\/p\u003e\u003cp\u003eInstall the SSH-6e directly on a compatible H6essential, H5studio, or H6studio recorder after confirming the recorder firmware meets Zoom's stated requirement. Set the recorder's side level to control the stereo width, select Mute for mono shotgun operation, or use Raw Mid-Side recording when you want to decode and adjust width later in a DAW. Fit the included WSU-2 hairy windscreen for outdoor recording where wind noise may affect the capture.\u003c\/p\u003e","brand":"Zoom","offers":[{"title":"Default Title","offer_id":45669289066566,"sku":"ZSSH6e","price":109.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61N1ZY1J8eL.jpg?v=1784488555"},{"product_id":"zoom-zum-2-usb-condenser-microphone","title":"Zoom ZUM-2 USB Condenser Microphone","description":"\u003cp\u003eThe Zoom ZUM-2 is a USB condenser microphone designed for direct recording, streaming, podcasting, voice-over work, online communication, and music creation with a computer. It connects through USB-C and is powered by the computer’s USB bus, eliminating the need for a separate audio interface or external microphone preamp. Its plug-and-play design helps simplify a desktop recording setup for creators who want a dedicated microphone rather than relying on a built-in computer mic.\u003c\/p\u003e\u003cp\u003eBuilt around a back electret condenser capsule, the ZUM-2 uses a supercardioid pickup pattern to focus on the sound in front of the microphone while reducing pickup from surrounding room noise and off-axis sources. This makes it well suited to close-miked spoken-word applications such as podcasts, livestreams, gaming chat, voice-over recording, and video calls. The side-address format supports natural placement on a desktop stand or compatible microphone arm.\u003c\/p\u003e\u003cp\u003eThe microphone supports 24-bit digital audio at sample rates up to 96 kHz, giving compatible recording software access to high-resolution capture settings. Its specified 20 Hz to 20 kHz frequency response covers the standard audible range, while its 135 dB SPL maximum rating provides headroom for louder vocal or instrument sources. The ZUM-2 records mono microphone audio through its USB connection.\u003c\/p\u003e\u003cp\u003eA built-in 3.5 mm stereo headphone output provides a convenient monitoring point directly on the microphone. The dedicated front-mounted headphone volume control lets users adjust the listening level without reaching for computer settings. This output is intended for monitoring computer audio through headphones connected to the microphone.\u003c\/p\u003e\u003cp\u003eThe included foam windscreen helps reduce breath noise and vocal plosives during close microphone use. Zoom also includes a USB Type-A to USB Type-C cable, a TPS-4 tabletop tripod mic stand, a pivoting stand mount, and a threaded adapter. Together, these accessories provide a ready-to-use desktop recording setup that can also be adapted for compatible microphone stands.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUSB-C Computer Connection:\u003c\/strong\u003e Connects directly to a computer without an audio interface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSupercardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the source while reducing unwanted surrounding sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24-Bit\/96 kHz Audio:\u003c\/strong\u003e Supports high-resolution recording in compatible software.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeadphone Monitoring Output:\u003c\/strong\u003e Provides a 3.5 mm stereo connection for headphones.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDedicated Volume Knob:\u003c\/strong\u003e Adjusts headphone listening level directly from the microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Desktop Accessories:\u003c\/strong\u003e Includes a windscreen, tripod stand, mount, adapter, and USB cable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe ZUM-2 has a black cylindrical body with a side-address microphone format, integrated blue power indicator, USB Type-C port, headphone output, and headphone volume knob. Its back electret condenser design and supercardioid pattern are intended for close, front-facing voice capture. The microphone measures 54 mm in diameter by 150 mm long and weighs 422 g.\u003c\/p\u003e\u003cp\u003eConnect the included USB Type-A to USB Type-C cable between the microphone and a compatible Mac or Windows computer, then select ZUM-2 as the input and output device in the operating system or recording application. Position the microphone with the speaking side facing the user and use the included foam windscreen for close vocal work. The included TPS-4 tabletop tripod and pivoting mount support desktop placement, while the supplied 5\/8-inch to 3\/8-inch threaded adapter helps accommodate compatible stand hardware.\u003c\/p\u003e","brand":"Zoom","offers":[{"title":"Default Title","offer_id":45669296078918,"sku":"ZUM2","price":49.99,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61vBd1JWENL.jpg?v=1784488768"},{"product_id":"mackie-em-carbon-premium-usb-condenser-microphone","title":"Mackie EM-Carbon Premium USB Condenser Microphone","description":"\u003cp\u003eThe Mackie EM-Carbon is a USB condenser microphone designed for recording, streaming, podcasting, voiceovers, interviews, and music creation. It connects directly to a computer through USB-C, avoiding the need for a separate audio interface for basic recording setups. Its included desktop stand and plug-and-play operation make it suitable for creators building a practical desktop recording system.\u003c\/p\u003e\u003cp\u003eThis side-address microphone uses a 14 mm condenser capsule and supports a 20 Hz to 20 kHz frequency response. It is suited to capturing spoken voice, vocals, instruments, and room sound with a detailed full-range presentation. The 126 dB maximum input SPL also gives it capacity for louder sound sources when gain is set appropriately.\u003c\/p\u003e\u003cp\u003eFive selectable polar patterns let the EM-Carbon adapt to different recording situations. Cardioid is useful for a single speaker or vocalist, while bidirectional can serve two-person interviews from opposite sides of the microphone. Stereo, super-cardioid, and omnidirectional modes broaden its use for instruments, field capture, group discussions, and ambient recording.\u003c\/p\u003e\u003cp\u003eOnyx microphone preamp circuitry and 16-bit\/48 kHz digital audio conversion provide the microphone's USB recording path. Front-panel gain, mute, and headphone-volume controls keep key adjustments within reach. The dedicated headphone output allows direct monitoring from the microphone while also playing computer audio.\u003c\/p\u003e\u003cp\u003eThe EM-Carbon fits naturally into a computer-based content-creation setup and can be used on its included stand or a standard microphone stand. It includes a USB-C cable with a USB-A computer connection, helping simplify initial setup. Mackie also includes Waveform OEM software and the DAW Essentials plugin bundle for users starting a recording workflow.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFive Polar Patterns:\u003c\/strong\u003e Select stereo, cardioid, figure-8, super-cardioid, or omnidirectional pickup for different sources and recording layouts.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e14 mm Condenser Capsule:\u003c\/strong\u003e Captures voice, instruments, and other detailed sound sources across a 20 Hz to 20 kHz response range.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUSB-C Connectivity:\u003c\/strong\u003e Connects directly to a compatible computer with a class-compliant, driver-free USB audio connection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOnyx Preamp Circuitry:\u003c\/strong\u003e Provides the microphone's integrated low-noise recording signal path.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeadphone Monitoring:\u003c\/strong\u003e Use the 1\/8-inch stereo headphone jack and independent volume control for convenient listening.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOnboard Controls:\u003c\/strong\u003e Gain, mute, polar-pattern, and headphone-volume controls support quick adjustments while recording.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe EM-Carbon has a black, side-address microphone design with an integrated standard microphone stand mount. Mackie describes its construction as rugged; the manufacturer does not specify a housing material composition. A red internal LED illuminates when the microphone mute switch is engaged.\u003c\/p\u003e\u003cp\u003eFor setup, connect the USB-C end of the included cable to the microphone and the USB-A end directly to an available computer USB port. Mackie advises connecting directly to the computer rather than through a USB hub or keyboard port. Position the microphone so the intended source addresses the side of the microphone, then select the polar pattern and adjust gain for the recording task.\u003c\/p\u003e","brand":"Mackie","offers":[{"title":"Default Title","offer_id":45669382783046,"sku":"CARBON","price":245.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/51kLnseXhwL.jpg?v=1784495700"},{"product_id":"mackie-em-91c-large-diaphragm-condenser-microphone","title":"Mackie EM-91C Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe Mackie EM-91C is a large-diaphragm condenser microphone designed for recording vocals, instruments, voice-overs, and room ambience. It provides an XLR-based microphone option for creators who need a dedicated studio-style mic rather than a USB desktop microphone. Its included shock mount and XLR cable help provide a practical starting point for a recording setup.\u003c\/p\u003e\u003cp\u003eThis microphone is suited to home studios, content creation, live streaming, and recording environments that use an audio interface, mixer, or preamp. It requires 48V phantom power, so it is intended for systems with a compatible XLR microphone input. The EM-91C can be used for vocal takes, stringed instruments, spoken-word work, and ambient capture.\u003c\/p\u003e\u003cp\u003eThe EM-91C uses a cardioid, unidirectional pickup pattern to focus on sound in front of the microphone while rejecting peripheral noise. This can help reduce unwanted surrounding sound in typical recording spaces. Mackie describes its performance character as capable of capturing warmth and brilliance on vocals along with detail from instruments.\u003c\/p\u003e\u003cp\u003eAt its core, the EM-91C uses a black electret condenser element with a 20 Hz to 18 kHz frequency response. It has a rated sensitivity of -30 dB and handles up to 134 dB SPL at 1 kHz with 1% THD. The microphone's 150-ohm output impedance and XLR connection support integration with standard phantom-powered recording equipment.\u003c\/p\u003e\u003cp\u003eThe EM-91C fits naturally into a system built around an interface or mixer with 48V phantom power. Start with the supplied XLR cable and shock mount, then add a suitable stand, boom arm, or pop filter as needed for the recording application. Its compact 6.1-inch body and low 0.46-pound weight make it straightforward to position in a vocal or instrument setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eLarge-Diaphragm Condenser:\u003c\/strong\u003e Captures vocals, instruments, voice-overs, and room ambience.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the intended source and rejects peripheral noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e48V Phantom Power:\u003c\/strong\u003e Works with compatible audio interfaces, mixers, and preamps.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e20 Hz–18 kHz Response:\u003c\/strong\u003e Covers a broad frequency range for recording applications.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e134 dB Maximum SPL:\u003c\/strong\u003e Supports recording of louder sound sources when properly positioned.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Recording Accessories:\u003c\/strong\u003e Includes a shock mount and XLR cable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe EM-91C has a black electret condenser element in a compact black microphone body. Mackie specifies a rugged construction, while the condenser design and large-diaphragm format are intended for detailed recording work. The microphone measures 6.1 inches high by 1.9 inches wide and weighs 0.46 pound.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included shock mount on a compatible microphone stand or boom arm. Connect the included XLR cable to the microphone and to an audio interface, mixer, or preamp that supplies 48V phantom power. Aim the front of the cardioid microphone toward the desired source, and use appropriate placement for vocals, instruments, or room capture.\u003c\/p\u003e","brand":"Mackie","offers":[{"title":"Default Title","offer_id":45669387337798,"sku":"EM-91C","price":143.18,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61wBOQzuhnL.jpg?v=1784497112"},{"product_id":"mackie-em-usb-usb-condenser-microphone","title":"Mackie EM-USB USB Condenser Microphone","description":"\u003cp\u003eThe Mackie EM-USB is a USB condenser microphone designed to record directly to a computer without requiring a separate audio interface. It provides a straightforward recording solution for home studios, podcasts, livestreams, video calls, and online content creation. USB-C connectivity and onboard controls keep the setup focused and uncluttered.\u003c\/p\u003e\u003cp\u003eA cardioid, unidirectional pickup pattern concentrates on sound in front of the microphone while helping reduce pickup from the sides and rear. This makes the EM-USB well suited to single-person voice recording, spoken-word work, and close-miked musical ideas. Its 14 mm condenser capsule covers a 30 Hz to 18 kHz frequency response.\u003c\/p\u003e\u003cp\u003eBuilt-in gain control lets users adjust microphone input sensitivity at the mic, helping match its output to a computer or recording application. A dedicated mute switch turns off the microphone signal while computer playback can still be heard through connected headphones. The power and mute LED gives a clear visual indication of operating status.\u003c\/p\u003e\u003cp\u003eThe integrated headphone output supports direct monitoring and computer playback through stereo headphones with a 1\/8-inch connector. Its independent headphone level control makes it easier to set a comfortable listening level without adjusting the computer's main output. With up to 400 mW of stereo output power, the EM-USB combines microphone and monitoring functions in one desktop-friendly device.\u003c\/p\u003e\u003cp\u003eThe EM-USB fits naturally into a compact creator setup, connecting to a computer through the included USB-C-to-USB-A cable. A tripod stand and mic clip are included for immediate desktop placement, while the mic clip can also support compatible stand or boom-mount use. Waveform OEM recording software and the DAW Essentials plugin bundle are included for users building a recording workflow.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eUSB-C Recording Interface:\u003c\/strong\u003e Connects directly to a computer for USB audio recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e14 mm Condenser Capsule:\u003c\/strong\u003e Captures detailed voice and instrument recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the source in front of the mic.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeadphone Monitoring:\u003c\/strong\u003e Provides a 1\/8-inch headphone output with level control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGain And Mute Controls:\u003c\/strong\u003e Adjust input sensitivity and silence the microphone quickly.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded Desktop Accessories:\u003c\/strong\u003e Comes with a tripod stand, mic clip, and USB cable.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe EM-USB uses a compact, rugged microphone body intended for regular desktop and portable recording use. Its controls and connections are placed on the microphone itself, including the USB-C port, headphone jack, headphone level knob, gain knob, mute switch, and status LED. The microphone measures 7.1 inches high by 1.8 inches wide and weighs 0.87 lb.\u003c\/p\u003e\u003cp\u003eFor setup, connect the included USB-C end of the cable to the microphone and the USB-A end directly to an available computer USB port. Connect stereo headphones with a 1\/8-inch plug for monitoring, then select the EM-USB as the computer's input and output device when needed. Use the included tripod stand for desktop recording, or use the supplied mic clip with a compatible microphone stand or boom.\u003c\/p\u003e","brand":"Mackie","offers":[{"title":"Default Title","offer_id":45669387370566,"sku":"EM-USB","price":268.48,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61fSJHzq_ZL.jpg?v=1784497145"},{"product_id":"se-electronics-gemini-ii-dual-tube-condenser-microphone","title":"sE Electronics GEMINI II Dual-Tube Condenser Microphone","description":"\u003cp\u003eThe sE Electronics GEMINI II is a large-diaphragm, cardioid tube condenser microphone designed for professional recording of vocals and instruments. It provides a dedicated studio microphone option for users who want tube-based character while retaining clear high-frequency detail. Its cardioid pickup pattern helps focus on the intended source and reduce pickup from the rear.\u003c\/p\u003e\u003cp\u003eThe GEMINI II is suited to vocal recording, acoustic instruments, electric guitar cabinets, drum rooms, piano, brass, woodwinds, strings, and orchestral work. Its switchable pad supports close placement and high-SPL sources, while its low-cut filter helps manage rumble, plosives, and proximity-effect buildup. This makes it adaptable for both detailed close-miking and broader room applications.\u003c\/p\u003e\u003cp\u003eIts sound design combines a 12AX7\/ECC83 input tube with a 12AU7\/ECC82 output-stage tube. The second tube performs the output-stage role typically handled by a transformer, supporting the microphone's extended high-frequency response. The result is a tube condenser design intended to balance weight and warmth with articulation.\u003c\/p\u003e\u003cp\u003eA handcrafted 1.4-inch true condenser capsule and gold-sputtered Mylar diaphragm form the core of the GEMINI II's capture system. The microphone has a 20 Hz to 20 kHz frequency range, 40 mV\/Pa sensitivity, and an equivalent noise level of 13 dB(A). Its 200-ohm electrical impedance is designed for connection to microphone preamps or audio interfaces with an input load above 1 k ohm.\u003c\/p\u003e\u003cp\u003eThe GEMINI II is a complete tube microphone system rather than a standalone XLR microphone. It uses the included floor-box power supply and 8-pin microphone cable, with the floor box connecting to a preamp, mixer, or audio interface through XLR. It is a practical upgrade path for recording setups that need a dedicated large-diaphragm tube microphone with its own external power system.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDual-Tube Circuit:\u003c\/strong\u003e Uses 12AX7 and 12AU7 tubes for tube-based input and output stages.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1.4-Inch True Condenser Capsule:\u003c\/strong\u003e Handcrafted large-diaphragm capsule captures detailed studio recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the source while reducing rear pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable -10 dB Pad:\u003c\/strong\u003e Helps accommodate close-miked and high-SPL sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e150 Hz Low-Cut Filter:\u003c\/strong\u003e Reduces rumble, plosives, footfall noise, and proximity-effect buildup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncluded External Power Supply:\u003c\/strong\u003e Powers the tube microphone without interface phantom power.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe GEMINI II uses a hand-made all-metal housing, gold-sputtered Mylar diaphragm, and gold-plated XLR connector. The microphone measures 80 mm in diameter and 220 mm long, with a weight of 1,180 g. A custom shock mount, wooden presentation box, and flight case are included to support placement, storage, and transport.\u003c\/p\u003e\u003cp\u003eMount the microphone securely with the included custom shock mount and connect it to the included floor box using the supplied 8-pin cable. Connect the floor box to a microphone preamp, mixer, or audio interface with an XLR cable, then connect the IEC power cable before switching on the power supply. Do not use external +48V phantom power, and allow approximately 15 minutes of warm-up time before recording for stable tube operation.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669430853702,"sku":"GEMINI II","price":1641.76,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81RJ6bUIlUL.jpg?v=1784502258"},{"product_id":"se-electronics-neom-usb-cardioid-usb-condenser-microphone","title":"sE Electronics NEOM USB Cardioid USB Condenser Microphone","description":"\u003cp\u003eThe sE Electronics NEOM USB is a plug-and-play USB condenser microphone for recording, streaming, podcasting, voice chat, and mobile content creation. Its integrated USB audio interface connects directly to compatible computers and mobile devices without requiring a separate microphone preamp or audio interface. It is designed for creators who want a compact desktop recording solution with direct headphone monitoring.\u003c\/p\u003e\u003cp\u003eA 16 mm back-electret condenser capsule and cardioid pickup pattern focus capture toward the front of the microphone while reducing sound arriving from the sides and rear. This makes the NEOM USB suited to close-miked speech, vocals, acoustic instruments, and other single-source recording tasks. The microphone is side-addressed, so the speaker or performer addresses the front surface above the controls rather than the top.\u003c\/p\u003e\u003cp\u003eThe integrated converter supports 24-bit recording and sample rates up to 192 kHz. Lower supported rates are also available for typical recording and streaming workflows, including 44.1 kHz and 48 kHz. For most applications, sE recommends using 48 kHz at 24-bit resolution.\u003c\/p\u003e\u003cp\u003eFront-panel controls make it possible to set microphone gain and create a personal headphone balance without changing the signal heard by an audience. Separate Mic Level and Playback Level controls adjust the direct microphone signal and computer playback in the headphone mix. A rear 1\/8-inch headphone output provides direct monitoring, while the illuminated sE logo functions as a mute button.\u003c\/p\u003e\u003cp\u003eThe NEOM USB includes a metal desktop stand, microphone clip, thread adapter, and USB-C to USB-A cable for a ready-to-use desktop setup. The clip can be removed for use with a full-size microphone stand, making the microphone adaptable to a desk, boom arm, or studio stand. For mobile and USB-C host devices, the appropriate USB-C, Lightning, or micro-USB cable or adapter may be needed.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e16 mm Cardioid Capsule:\u003c\/strong\u003e Captures a focused front-facing source while reducing pickup from the sides and rear.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e24-Bit \/ 192 kHz Audio:\u003c\/strong\u003e Supports high-resolution digital recording through its built-in USB audio interface.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDirect Headphone Monitoring:\u003c\/strong\u003e The 1\/8-inch headphone output lets users monitor from the microphone rather than computer audio.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndependent Monitor Mix:\u003c\/strong\u003e Mic Level and Playback Level controls adjust the headphone blend independently.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUSB-C Connectivity:\u003c\/strong\u003e Connects to compatible Mac, Windows, iOS, and Android devices with suitable cables or adapters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIntegrated Shock Isolation:\u003c\/strong\u003e The internally mounted capsule helps reduce rumble and handling-related vibration.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe NEOM USB combines a 16 mm back-electret condenser capsule with an internal shock-mount system in a compact side-address microphone body. Its included desktop stand is metal and uses rubber feet to help minimize vibration transfer from the desk. The microphone also provides an LED gain indication and a logo-mounted mute control for clear operational feedback.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a compatible USB-equipped computer or mobile device, then select it as the input and output device in the recording or streaming software as needed. Use the included USB-C to USB-A cable for USB-A hosts; USB-C, Lightning, or micro-USB devices require the appropriate cable or adapter. Position the front of the microphone about 6 inches from the speaker or singer, set gain so the LED does not flash red, and use a pop filter when recording vocals if desired.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669431377990,"sku":"NEOM USB","price":95.38,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71JqASMCXqL.jpg?v=1784502516"},{"product_id":"se-electronics-rn17-cardioid-small-diaphragm-condenser-mic","title":"sE Electronics RN17 Cardioid Small-Diaphragm Condenser Mic","description":"\u003cp\u003eThe sE Electronics RN17 is a small-diaphragm condenser microphone designed for detailed studio and live sound capture. It is supplied with a cardioid capsule for focused pickup of a source while reducing pickup from the sides and rear. The RN17 is suited to engineers, musicians, and production teams that need a compact XLR microphone for close or spot miking.\u003c\/p\u003e\u003cp\u003eIts cardioid response and 20 Hz to 20 kHz frequency range make it a practical choice for acoustic guitar, piano, strings, woodwinds, percussion, drum overheads, and choir work. The microphone is built to capture fast transients and fine high-frequency detail while retaining a full low-frequency presentation. A 131 dB maximum SPL rating at 0.5% THD allows it to be used on many high-level acoustic and percussion sources.\u003c\/p\u003e\u003cp\u003eThe RN17 was developed as part of the sE Electronics and Rupert Neve collaboration. Its design combines a hand-crafted true-condenser capsule with a full-scale custom transformer designed for the microphone. This transformer-based circuit is intended to provide headroom, defined midrange detail, and balanced low-frequency response.\u003c\/p\u003e\u003cp\u003eThe included cardioid capsule is the standard configuration for this single-microphone package. An omnidirectional capsule is available separately for applications where a more open pickup pattern is preferred. This gives users an upgrade path without replacing the microphone body.\u003c\/p\u003e\u003cp\u003eFor practical recording setups, the RN17 connects through a standard 3-pin XLR output and requires 48V phantom power. A dedicated shock mount is included to help reduce vibration transferred through a microphone stand. The microphone, wooden box, metal case, thread adapter, and user manual provide a complete protected starting package for studio or stage use.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Capsule:\u003c\/strong\u003e Focuses capture on the intended source and helps reduce surrounding pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTrue Condenser Design:\u003c\/strong\u003e Provides the sensitivity required for detailed instrument and ensemble recording.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCustom Rupert Neve Transformer:\u003c\/strong\u003e Supports balanced output, headroom, and a full-frequency presentation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGold-Sputtered Diaphragm:\u003c\/strong\u003e Designed for rapid transient response and high-frequency detail.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e48V Phantom Power:\u003c\/strong\u003e Works with compatible XLR microphone preamps, mixers, and audio interfaces.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCustom Shock Mount:\u003c\/strong\u003e Helps limit stand-borne vibration and handling noise during recording.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe RN17 uses a hand-crafted true-condenser capsule, an unusually substantial transformer housing, and a matte black finish intended to remain visually unobtrusive on stage or in the studio. Its microphone body measures 200 mm long, with a 44 mm transformer diameter and 17 mm capsule diameter. A wooden box and metal case are included for storage and transport.\u003c\/p\u003e\u003cp\u003eMount the RN17 in its included custom shock mount on a stable microphone stand, using the included thread adapter when needed. Connect its 3-pin male XLR output to a compatible microphone preamp, mixer, or audio interface, then supply 48V phantom power. Use the supplied cardioid capsule for focused spot miking, or add the separately available omnidirectional capsule when a more open pickup pattern is needed.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669435605062,"sku":"RN17","price":999.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71swgbvM-TL.jpg?v=1784502859"},{"product_id":"se-electronics-rn17-cardioid-15mm-condenser-capsule","title":"SE Electronics RN17 Cardioid 15mm Condenser Capsule","description":"\u003cp\u003eThe SE Electronics RN17 Cardioid is a replacement and expansion capsule made specifically for the RN17 small-diaphragm condenser microphone. It provides a cardioid pickup pattern for recording a focused source while reducing pickup from the sides and rear. This single capsule is intended for owners of an RN17 microphone body, not as a standalone microphone.\u003c\/p\u003e\u003cp\u003eIts compact 15 mm gold-sputtered diaphragm is designed for fast response to transients and detailed high-frequency capture. The cardioid pattern suits close and spot miking applications where source focus and off-axis rejection are useful. It is a practical option for acoustic instruments, percussion, vocals, piano, and drum overhead use.\u003c\/p\u003e\u003cp\u003eThe capsule is a true-condenser design, hand-crafted and individually tuned for consistency. A brass housing provides a durable physical structure and helps shield the capsule from electrical interference. When installed on the compatible RN17 body, it supports the RN17 system's 20 Hz to 20 kHz frequency range.\u003c\/p\u003e\u003cp\u003eWith the RN17 microphone system, the cardioid capsule is specified for 131 dB maximum SPL at 0.5% THD and an 18 dB equivalent noise level. These characteristics make it suitable for detailed recording work as well as many live-sound microphone applications. The RN17 microphone body supplies the required phantom-powered electronics and XLR output connection.\u003c\/p\u003e\u003cp\u003eThis capsule is useful as a replacement cardioid option or for expanding an existing RN17 setup. It can also support a matched multi-microphone workflow when used with compatible RN17 equipment. The optional RN17 omnidirectional capsule is sold separately for users who need a more open pickup pattern.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRN17-Specific Fit:\u003c\/strong\u003e Designed for use with the SE Electronics RN17 small-diaphragm condenser microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup:\u003c\/strong\u003e Focuses on the intended source while reducing off-axis sound pickup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 mm Diaphragm:\u003c\/strong\u003e Gold-sputtered diaphragm supports detailed transient and high-frequency reproduction.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTrue-Condenser Design:\u003c\/strong\u003e Provides the operating characteristics of the compatible RN17 condenser system.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHandcrafted Construction:\u003c\/strong\u003e Individually tuned capsule construction supports consistent performance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBrass Housing:\u003c\/strong\u003e Durable housing helps provide shielding from electrical interference.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe RN17 Cardioid capsule uses a compact brass housing and gold-sputtered diaphragm construction. Its brass finish is distinct from the matte-black finish of the complete RN17 microphone body. This product is the capsule only; it does not include an RN17 microphone body, shock mount, cable, or stand mount.\u003c\/p\u003e\u003cp\u003eInstall the capsule only on a compatible SE Electronics RN17 microphone body according to the RN17 system instructions. The completed RN17 microphone connects to a microphone preamp or audio interface through XLR and requires 48 V phantom power. Use the cardioid capsule for close instrument, vocal, percussion, piano, and overhead placements where directional pickup is preferred.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669435637830,"sku":"RN17 Cardioid","price":269.95,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/819aMo2vRQL.jpg?v=1784502900"},{"product_id":"se-electronics-rn17p-matched-pair-condenser-microphones","title":"sE Electronics RN17(P) Matched Pair Condenser Microphones","description":"\u003cp\u003eThe sE Electronics RN17(P) is a factory-matched stereo pair of small-diaphragm condenser microphones designed for detailed instrument, ensemble, and ambient recording. Each microphone ships with a cardioid capsule and is engineered for stereo applications where close tonal consistency between microphones matters. The pair is suited to acoustic guitar, piano, strings, choir, woodwinds, percussion, drum overheads, and room capture.\u003c\/p\u003e\u003cp\u003eThe RN17 combines a compact capsule with a large custom output transformer, addressing the lean low-frequency character sometimes associated with small-diaphragm microphones. Its cardioid pickup pattern helps focus on the intended source while reducing sound arriving from the rear. With a 20 Hz to 20 kHz frequency range and 131 dB maximum SPL handling, it can cover delicate acoustic sources as well as louder instruments.\u003c\/p\u003e\u003cp\u003eDeveloped as part of the sE Electronics and Rupert Neve collaboration, the RN17 uses Class-A electronics and a custom-designed transformer. The microphone's 15 mm gold-sputtered diaphragm is intended to respond quickly to transients and fine high-frequency detail. Its stated sound character balances detailed mids and highs with full, accurate low-end response.\u003c\/p\u003e\u003cp\u003eThis RN17(P) package is factory matched as a stereo pair, with the transformers and cardioid capsules matched for close tolerance. That makes it practical for coincident, near-coincident, spaced-pair, and overhead recording techniques. A precision stereo mounting bar is included to position both microphones from a single stand.\u003c\/p\u003e\u003cp\u003eEach RN17 requires standard 48 V phantom power from a compatible microphone preamp, mixer, audio interface, or recorder. The microphones connect using standard 3-pin XLR microphone cables. An optional omnidirectional capsule is available separately for users who need a more open pickup pattern for room, ensemble, or ambient recording.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFactory-Matched Stereo Pair:\u003c\/strong\u003e Transformers and cardioid capsules are matched for closely aligned stereo recording performance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e15 mm Gold-Sputtered Diaphragm:\u003c\/strong\u003e The compact diaphragm supports fast transient response and detailed capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCustom Output Transformer:\u003c\/strong\u003e A full-scale Rupert Neve-designed transformer supports balanced frequency response and headroom.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Capsule Included:\u003c\/strong\u003e Focuses on the source while reducing pickup from the rear of each microphone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOptional Omni Capsule Support:\u003c\/strong\u003e Expand the system with separately available omnidirectional RN17 capsules.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Stereo Accessories:\u003c\/strong\u003e Includes two shock mounts, a stereo bar, presentation case, and flight case.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe RN17 uses a hand-crafted 2\/3-inch true-condenser capsule, Class-A electronics, and a matte black finish intended to remain visually unobtrusive on stage or in the studio. Each microphone measures 200 mm long and weighs 320 g. The included custom shock mounts help isolate the microphones from stand-borne vibration and handling noise.\u003c\/p\u003e\u003cp\u003eConnect each RN17 to a separate balanced XLR microphone input and enable 48 V phantom power only on compatible equipment. Use the included stereo mounting bar for paired configurations; its microphone-mount spacing adjusts from 58 mm to 276 mm. The supplied thread adapters allow the shock mounts and stereo bar to be fitted to compatible microphone stands.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669438554182,"sku":"RN17(P)","price":2199.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/61wtS9vpwzL.jpg?v=1784503350"},{"product_id":"se-electronics-rnt-multi-pattern-tube-condenser-microphone","title":"sE Electronics RNT Multi-Pattern Tube Condenser Microphone","description":"\u003cp\u003eThe sE Electronics RNT is a large-diaphragm tube condenser microphone designed for professional studio recording of vocals and instruments. It combines a hand-crafted 1-inch true condenser capsule with tube and discrete Class-A amplification stages. Its included external Floor Box power supply provides the controls and connections needed for a complete recording setup.\u003c\/p\u003e\u003cp\u003eThe RNT is suited to vocal tracking, acoustic instruments, guitar cabinets, piano, strings, woodwinds, percussion, drum overheads, toms, and room recording. Nine selectable polar-pattern positions allow the microphone to capture anything from a focused source to a wider balance of direct and ambient sound. This flexibility helps one microphone serve several roles in a studio locker.\u003c\/p\u003e\u003cp\u003eA hand-selected 12AU7\/ECC82 tube operates within the microphone body, while the external Floor Box contains the second active stage. Both stages use fully discrete Class-A electronics, and the Floor Box uses custom op-amp cards associated with Rupert Neve Designs' 5088 console. Custom Rupert Neve Designs transformers are used in the microphone and Floor Box signal stages.\u003c\/p\u003e\u003cp\u003eThe RNT provides switchable gain settings of -12 dB, 0 dB, and +12 dB to accommodate quieter sources and high-SPL close-miking situations. Its selectable 40 Hz and 80 Hz low-cut filters can help reduce rumble, footfall noise, wind noise, plosives, and excess proximity effect. With a maximum SPL rating of 151 dB SPL at 0.5% THD, it is specified for demanding recording applications.\u003c\/p\u003e\u003cp\u003eThe microphone connects to its included Floor Box with the supplied 8-pin cable, while the Floor Box sends balanced audio from its 3-pin XLR output to a microphone preamp or audio interface. No phantom power is required from the connected preamp or interface. A custom shock mount, wooden microphone box, flight case, IEC power cable, and related accessories are included for storage and setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch True Condenser Capsule:\u003c\/strong\u003e Hand-crafted large-diaphragm capsule captures detailed studio recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNine Polar Patterns:\u003c\/strong\u003e Select omni, cardioid, figure-eight, or intermediate positions.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e12AU7\/ECC82 Tube:\u003c\/strong\u003e Hand-selected tube forms the microphone's first active stage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClass-A Signal Path:\u003c\/strong\u003e Fully discrete electronics are used in both active stages.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Gain:\u003c\/strong\u003e -12 dB, 0 dB, and +12 dB settings broaden usability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLow-Cut Filters:\u003c\/strong\u003e Switchable 40 Hz and 80 Hz filtering reduces unwanted low frequencies.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe RNT uses a sturdy all-metal microphone body and an external metal Floor Box power supply. Its microphone body measures 62 mm in diameter and 240 mm long, while the included custom shock mount helps isolate the microphone from stand-borne vibration. A wooden microphone box and flight case are included for protected storage and transport.\u003c\/p\u003e\u003cp\u003eMount the microphone in the supplied shock mount on a stable microphone stand, then connect the supplied 8-pin cable between the microphone and Floor Box. Connect the Floor Box to AC power with the included IEC cable and run a standard balanced XLR cable from the Floor Box output to a microphone preamp or audio interface. Do not apply phantom power from the connected interface or preamp; allow approximately 15 minutes of warm-up time before recording for the tube to stabilize.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669438619718,"sku":"RNT","price":2799.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/71TrzPBrDBL.jpg?v=1784503431"},{"product_id":"se-electronics-se-se8-small-diaphragm-condenser-microphone","title":"sE Electronics SE-sE8 Small-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe sE Electronics sE8 is a cardioid small-diaphragm true condenser microphone for detailed studio recording and live sound reinforcement. It is designed for acoustic guitar, piano, strings, woodwinds, percussion, cymbals, drum overheads, and other sources where articulation and transient response matter. Its compact pencil-style format makes it practical for close placement in tight microphone positions.\u003c\/p\u003e\u003cp\u003eThe sE8 is intended for musicians, engineers, and venues that need a versatile condenser microphone with a balanced, controlled sound character. Its hand-crafted 1\/2-inch capsule and precision backplate design are made to support a natural response with consistent off-axis pickup. This makes it useful when a source needs to sit clearly in a recording or live mix without relying on excessive tonal coloration.\u003c\/p\u003e\u003cp\u003eTransformerless Class-A electronics support a clean signal path with low self-noise and strong dynamic-range performance. The microphone is rated for 13 dB(A) equivalent noise and up to 159 dB SPL when its -20 dB pad is engaged. Those specifications make it suitable for both quieter acoustic material and high-level sources such as snare, brass, and guitar cabinets.\u003c\/p\u003e\u003cp\u003eTwo switchable attenuation pads and two low-cut filter settings provide practical control at the microphone. The -10 dB and -20 dB pads help prevent overload on loud sources, while the 80 Hz and 160 Hz filters can reduce rumble, footfall noise, wind noise, and excess proximity-effect bass. These controls allow the sE8 to adapt to a range of placement distances and recording environments.\u003c\/p\u003e\u003cp\u003eThe sE8 connects by standard 3-pin XLR and requires 48V phantom power from a compatible audio interface, mixer, or external phantom-power supply. Its all-metal body and gold-plated XLR connector are suited to regular studio and stage use. For expanded flexibility, it is compatible with the optional sE8 omni capsule, while matched-pair versions are available for stereo recording applications.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHand-Crafted True Condenser Capsule:\u003c\/strong\u003e A 1\/2-inch capsule supports detailed capture for instruments and percussion.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the intended source while reducing sound from the rear.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Input Pads:\u003c\/strong\u003e -10 dB and -20 dB settings help handle loud sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Low-Cut Filters:\u003c\/strong\u003e 80 Hz and 160 Hz filters reduce rumble and bass buildup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTransformerless Class-A Circuitry:\u003c\/strong\u003e Provides a clean signal path with high dynamic-range capability.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOptional Omni Capsule Compatibility:\u003c\/strong\u003e Supports an alternate omnidirectional capsule for expanded recording options.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE8 uses an all-metal chassis, a hand-crafted gold-sputtered condenser capsule, and a gold-plated 3-pin XLR connector. Its body measures 23 mm in diameter by 120 mm long and weighs 141 g. The single-microphone package includes a mic clip with thread adapter and a windscreen.\u003c\/p\u003e\u003cp\u003eMount the sE8 in its included clip on a suitable microphone stand, then connect it to a balanced XLR microphone input that supplies 48V phantom power. Use the pad for close-miking high-SPL instruments or when protecting an interface or mixer input from overload. Select the low-cut filter when rumble, wind noise, footfall noise, or close-placement bass buildup is present.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669438849094,"sku":"SE-sE8","price":243.2,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/713jBznEH8L.jpg?v=1784503475"},{"product_id":"se-electronics-se2200-large-diaphragm-condenser-microphone","title":"sE Electronics sE2200 Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe sE Electronics sE2200 is a large-diaphragm, cardioid condenser microphone designed for studio recording, voiceover work, streaming, and close-miking instruments. Its fixed cardioid pickup pattern focuses on the source in front of the capsule while helping reduce pickup from the sides and rear. It is a practical choice for creators who need a detailed XLR microphone for vocals, spoken word, acoustic instruments, and amplified sources.\u003c\/p\u003e\u003cp\u003eA hand-crafted 1-inch true condenser capsule gives the sE2200 its high-sensitivity studio-microphone operation. The capsule uses dual gold-sputtered diaphragms, individually tuned by sE Electronics, despite the microphone's cardioid-only pattern. The result is a balanced, open response suited to capturing vocal detail and the natural character of instruments.\u003c\/p\u003e\u003cp\u003eThe sE2200 uses a traditional discrete Class-A circuit design without integrated circuits, together with a custom-built output transformer. This engineering is intended to provide low-noise operation, useful sensitivity, and a full-bodied signal character. Its 20 Hz to 20 kHz frequency range supports recording duties from low instruments through detailed vocal and acoustic material.\u003c\/p\u003e\u003cp\u003eTwo switchable attenuation settings make the microphone more adaptable when recording loud sources. The -10 dB and -20 dB pads increase headroom for applications such as guitar cabinets, brass, drum overheads, and close-miked drums. Switchable 80 Hz and 160 Hz low-cut filters help reduce rumble, footfall noise, plosives, and excessive proximity-effect bass.\u003c\/p\u003e\u003cp\u003eThis microphone connects through a standard 3-pin XLR output and requires 48 V phantom power from a compatible audio interface, mixer, or dedicated preamp. The included sE Isolation Pack combines a shockmount with an adjustable metal pop filter for vocal recording setups. It can serve as a primary studio vocal microphone or as a flexible addition to a recording rig that already has XLR preamps and phantom power.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch True Condenser Capsule:\u003c\/strong\u003e Hand-crafted capsule captures detailed vocal and instrument recordings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup on the source positioned in front.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiscrete Class-A Electronics:\u003c\/strong\u003e Uses selected components without integrated circuits.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCustom Output Transformer:\u003c\/strong\u003e Adds transformer-coupled output stage to the microphone design.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Pads:\u003c\/strong\u003e -10 dB and -20 dB settings support louder sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Low-Cut Filters:\u003c\/strong\u003e 80 Hz and 160 Hz filtering helps manage low-frequency noise.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE2200 has a heavily shielded all-metal housing with a premium finish and a gold-plated 3-pin XLR connector. Its 51 mm diameter body measures 215 mm long and weighs 611 g. The included Isolation Pack uses a quick-release shockmount and an all-metal adjustable pop filter that can also be removed when not needed.\u003c\/p\u003e\u003cp\u003eMount the microphone in the included shockmount on a stable microphone stand or boom, then connect it with a balanced XLR microphone cable to an interface, mixer, or microphone preamp. Enable 48 V phantom power only through compatible equipment, and select the pad or low-cut setting as needed for the source and recording distance. For vocals, position the pop filter between the performer and microphone; for loud instruments, start with the appropriate attenuation pad engaged.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669438980166,"sku":"sE2200","price":293.02,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81bEqtoqmYL.jpg?v=1784503569"},{"product_id":"se-electronics-se2300-multi-pattern-condenser-microphone","title":"sE Electronics sE2300 Multi-Pattern Condenser Microphone","description":"\u003cp\u003eThe sE Electronics sE2300 is a large-diaphragm, multi-pattern condenser microphone designed for studio recording, voice work, and close-miking instruments. It gives creators one microphone platform for vocals, acoustic instruments, guitar cabinets, drums, brass, piano, and room capture. Its selectable pickup patterns help adapt the microphone to different recording spaces and source-placement needs.\u003c\/p\u003e\u003cp\u003eA hand-crafted 1-inch true condenser capsule is individually tuned and paired with discrete Class-A electronics. The design uses a custom output transformer and a short, optimized signal path to support detailed, balanced capture with low self-noise. This makes the sE2300 suitable for sessions where a clear, controlled condenser sound is needed across multiple sources.\u003c\/p\u003e\u003cp\u003eThree selectable polar patterns—cardioid, omnidirectional, and figure-8—provide practical flexibility. Cardioid can focus on a source while reducing pickup from behind the microphone, omnidirectional can capture a more open sound, and figure-8 supports front-and-rear pickup techniques. This versatility is useful for solo vocals, room ambience, duets, and stereo recording methods.\u003c\/p\u003e\u003cp\u003eThe sE2300 includes switchable -10 dB and -20 dB attenuation pads for louder sources. Its 80 Hz and 160 Hz low-cut filter settings help reduce rumble, footfall noise, and excess low-frequency buildup from close placement. Together, these controls allow the microphone to be used nearer to loud instruments and amplifiers with more control over the recorded signal.\u003c\/p\u003e\u003cp\u003eBuilt for home studios, commercial studios, and portable recording setups, the sE2300 connects through a standard 3-pin XLR output and requires 48V phantom power. The included Isolation Pack combines a shockmount and adjustable metal pop filter to support stable vocal recording. It is a practical upgrade for users who need more pattern and level-control options than a fixed-cardioid condenser microphone provides.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree Polar Patterns:\u003c\/strong\u003e Select cardioid, omnidirectional, or figure-8 pickup for different sources and recording techniques.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch True Condenser Capsule:\u003c\/strong\u003e Hand-crafted and individually tuned for consistent large-diaphragm condenser performance.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDiscrete Class-A Circuitry:\u003c\/strong\u003e Uses a traditional Class-A design without integrated circuits.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Attenuation Pads:\u003c\/strong\u003e -10 dB and -20 dB settings support close-miking of louder sound sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Low-Cut Filters:\u003c\/strong\u003e 80 Hz and 160 Hz filters help manage rumble and proximity-effect buildup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIsolation Pack Included:\u003c\/strong\u003e Includes a quick-release shockmount and adjustable all-metal pop filter.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE2300 uses a hand-crafted true condenser capsule, custom output transformer, and all-metal shielded housing. Its metal chassis is designed to help reduce electrical interference while providing a durable platform for studio and stage use. Front and rear switches provide direct access to pad, filter, and polar-pattern settings.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a compatible XLR microphone preamp, mixer, recorder, or audio interface that supplies 48V phantom power. Use the included shockmount to isolate the microphone from stand-borne vibration, then position the pop filter for vocal work or remove it when preferred. Start with cardioid for most single-source recording, then use the pad and low-cut controls as needed for loud or close-miked sources.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669439078470,"sku":"sE2300","price":387.16,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/812rkxbHowL.jpg?v=1784503604"},{"product_id":"se-electronics-se4100-large-diaphragm-condenser-microphone","title":"sE Electronics sE4100 Large-Diaphragm Condenser Microphone","description":"\u003cp\u003eThe sE Electronics sE4100 is a large-diaphragm true condenser microphone designed for studio recording and live sound applications. Its fixed cardioid pickup pattern focuses on the intended source while helping reduce pickup from the sides and rear. It is suited to recording vocals, acoustic instruments, piano, brass, guitar cabinets, and drum overheads.\u003c\/p\u003e\u003cp\u003eThis microphone is for creators, engineers, musicians, and live-sound users who need a versatile XLR condenser microphone without multiple polar-pattern controls. The cardioid-only design keeps operation straightforward while retaining the core recording features needed for close-miking and high-SPL sources. It can be used as a primary vocal microphone or as part of a larger recording setup.\u003c\/p\u003e\u003cp\u003eThe sE4100 uses a hand-crafted 1-inch gold-sputtered true condenser capsule with a gold-sputtered Mylar diaphragm. Its published response extends from 20 Hz to 20 kHz, with a sensitivity of 25 mV\/Pa. The microphone is specified for a smooth sound character and can accommodate both detailed acoustic material and louder amplified instruments.\u003c\/p\u003e\u003cp\u003eSwitchable low-cut filters at 80 Hz and 160 Hz help manage rumble, footfall noise, and proximity-related bass buildup. Selectable -10 dB and -20 dB attenuation pads increase the microphone's ability to handle loud sources. With the pad settings, maximum SPL handling reaches up to 157 dB SPL at 0.5% THD.\u003c\/p\u003e\u003cp\u003eThe sE4100 connects through a standard 3-pin male XLR output and requires 48V phantom power. It works with a microphone preamp, audio interface, mixer, or recorder that supplies P48 power and accepts balanced XLR microphone connections. A factory matched-pair version is also available for stereo overhead, room, and instrument-miking applications.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch True Condenser Capsule:\u003c\/strong\u003e Hand-crafted gold-sputtered capsule supports detailed capture across a broad range of sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Polar Pattern:\u003c\/strong\u003e Focuses pickup toward the source and helps reduce surrounding bleed.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Low-Cut Filters:\u003c\/strong\u003e Selectable 80 Hz and 160 Hz filters help control rumble and excess low end.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Attenuation Pads:\u003c\/strong\u003e -10 dB and -20 dB pads support recording louder instruments and amplifiers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Capability:\u003c\/strong\u003e Handles up to 157 dB SPL with the 20 dB pad engaged.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCustom Shockmount Included:\u003c\/strong\u003e Provides suspended mounting and includes a thread adapter for stand setup.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE4100 has a die-cast all-metal housing, metal switches, and a spring-steel wire-mesh grille. Its compact flat, round-edged chassis is designed for practical positioning around instruments, amplifiers, and drum kits. The microphone includes a metal case for storage and transport.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a balanced XLR microphone input that provides 48V phantom power according to IEC 61938. Use the included custom shockmount and thread adapter with a compatible microphone stand or boom, then select the low-cut filter and attenuation pad appropriate for the source. For stereo recording, the separately available matched-pair configuration includes two microphones, two shockmounts, a stereo mounting bar, and a metal case.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669439111238,"sku":"sE4100","price":349.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81PuzT0jGKL.jpg?v=1784503642"},{"product_id":"se-electronics-se4100-matched-pair-condenser-microphones","title":"sE Electronics sE4100 Matched Pair Condenser Microphones","description":"\u003cp\u003eThe sE Electronics sE4100(P) is a factory-matched pair of large-diaphragm condenser microphones for stereo recording and live sound applications. Each microphone uses a cardioid pickup pattern to focus on the intended source while helping reduce sound arriving from the rear and sides. The pair is suited to drum overheads, acoustic instruments, piano, guitar cabinets, brass, woodwinds, orchestral work, and vocals.\u003c\/p\u003e\u003cp\u003eBuilt around a hand-crafted 1-inch gold-sputtered true-condenser capsule, the sE4100 is designed for smooth, natural capture across a broad 20 Hz to 20 kHz frequency range. Its 25 mV\/Pa sensitivity and 9 dB(A) equivalent noise level support detailed recording of both close-miked and more nuanced sources. The cardioid-only design keeps operation straightforward for common studio and stage miking tasks.\u003c\/p\u003e\u003cp\u003eSwitchable low-cut filters at 80 Hz and 160 Hz help reduce rumble, stand vibration, and excessive proximity effect at the microphone. Selectable -10 dB and -20 dB attenuation pads increase headroom for louder sources such as drums, brass, and amplified guitar cabinets. With the pads engaged, maximum SPL capability reaches up to 147 dB or 157 dB at 0.5% THD, depending on the selected setting.\u003c\/p\u003e\u003cp\u003eThe matched-pair configuration is tested and tuned in-house for closely aligned frequency response between the two microphones. This consistency is useful when building stereo arrays for overheads, room capture, acoustic ensembles, and instrument spot miking. A stereo mounting bar is included to support compact stereo microphone placement.\u003c\/p\u003e\u003cp\u003eEach microphone connects through a standard 3-pin male XLR output and requires 48V phantom power. The pair can be integrated with a microphone preamp, audio interface, mixer, or recorder that supplies IEC 61938-compliant P48 power. Custom shockmounts help isolate the microphones from stand-borne vibration while supporting close placement around drums and amplifiers.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFactory-Matched Pair:\u003c\/strong\u003e Two microphones are tuned for closely matched frequency response in stereo applications.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch True-Condenser Capsule:\u003c\/strong\u003e Hand-crafted gold-sputtered capsule captures detailed vocals and instruments.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCardioid Pickup Pattern:\u003c\/strong\u003e Focuses on the source while helping reduce unwanted off-axis sound.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Low-Cut Filters:\u003c\/strong\u003e 80 Hz and 160 Hz settings help manage rumble and proximity effect.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Attenuation Pads:\u003c\/strong\u003e -10 dB and -20 dB pads accommodate high-SPL sources.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eComplete Stereo Kit:\u003c\/strong\u003e Includes two shockmounts, thread adapters, stereo bar, and metal case.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE4100 uses a die-cast all-metal housing, metal switches, and a spring-steel wire-mesh grille. Its flat, round-edged chassis is designed to work with the included custom suspension shockmount. The matched-pair kit stores both microphones and accessories in its supplied metal case.\u003c\/p\u003e\u003cp\u003eConnect each microphone to a balanced XLR microphone input that provides 48V phantom power, then mount the pair using the included shockmounts and stereo bar. Choose the low-cut filter and pad setting before recording based on source level, low-frequency buildup, and microphone distance. For stereo capture, position the microphones according to the desired technique and maintain consistent placement relative to the sound source.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669442650182,"sku":"sE4100(P)","price":563.31,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81gJ-MNmSsL.jpg?v=1784503682"},{"product_id":"se-electronics-se4400-1-multi-pattern-condenser-microphone","title":"sE Electronics sE4400 1\" Multi-Pattern Condenser Microphone","description":"\u003cp\u003eThe sE Electronics sE4400 is a large-diaphragm true condenser microphone built for detailed studio and live recording. Its selectable pickup patterns let one microphone adapt to close-miked sources, room capture, stereo techniques, and situations where off-axis rejection matters. It is suited to recording vocals, acoustic instruments, piano, drums, brass, and guitar cabinets.\u003c\/p\u003e\u003cp\u003eThis microphone is designed for engineers, musicians, producers, and content creators who need flexible microphone placement without changing the tonal foundation of their setup. The hand-crafted dual-diaphragm, gold-sputtered capsule is individually tuned in-house. Its response is intended to provide a smooth, natural character with clear source detail.\u003c\/p\u003e\u003cp\u003eFour selectable polar patterns—cardioid, hypercardioid, omnidirectional, and figure-8—support a broad range of recording approaches. Cardioid and hypercardioid modes can help focus on a source, while omnidirectional and figure-8 modes offer options for room sound and two-sided capture. This flexibility makes the sE4400 useful for both single-mic sessions and more involved studio setups.\u003c\/p\u003e\u003cp\u003eSwitchable 40 Hz and 80 Hz low-cut filters help reduce low-frequency rumble, footfall noise, and excessive proximity effect. Selectable 10 dB and 20 dB attenuation pads increase its ability to accommodate louder sources. With the 20 dB pad engaged, the microphone is rated for up to 157 dB SPL at 0.5% THD.\u003c\/p\u003e\u003cp\u003eThe sE4400 connects through a standard 3-pin XLR output and requires 48V phantom power from a compatible audio interface, mixer, or microphone preamp. Its included shockmount supports isolated mounting for studio stands and close-miking positions. A matched-pair version is also available for users building a stereo recording setup.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHand-Crafted Dual-Diaphragm Capsule:\u003c\/strong\u003e A 1-inch gold-sputtered true condenser capsule captures detailed, balanced audio.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour Polar Patterns:\u003c\/strong\u003e Select cardioid, hypercardioid, omnidirectional, or figure-8 operation for different miking methods.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Low-Cut Filters:\u003c\/strong\u003e Choose 40 Hz or 80 Hz filtering to reduce unwanted low-frequency content.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 dB and 20 dB Pads:\u003c\/strong\u003e Handles louder sound sources with increased headroom.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh SPL Capability:\u003c\/strong\u003e Supports up to 157 dB SPL with the 20 dB pad engaged.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCustom Shockmount Included:\u003c\/strong\u003e Helps reduce mechanically transmitted vibration during recording.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE4400 uses a die-cast all-metal housing, metal switches, and a spring-steel wire-mesh grille. Its flat, round-edged chassis is designed to work with the included custom shockmount and to support close placement against sources such as guitar cabinets or drum heads. The microphone measures 146 mm long and weighs 290 g.\u003c\/p\u003e\u003cp\u003eConnect the microphone to a compatible mixer, preamp, or audio interface using a balanced 3-pin XLR microphone cable, then enable 48V phantom power. Start in cardioid mode for a focused vocal or instrument capture, and use the low-cut filters or pads only when the source and placement call for them. For stereo recording, use two microphones or the separately available matched-pair configuration with its stereo mounting bar.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669442912326,"sku":"sE4400","price":428.12,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/716JVJ-d6rL.jpg?v=1784503718"},{"product_id":"se-electronics-se4400p-matched-pair-condenser-microphones","title":"sE Electronics sE4400(P) Matched Pair Condenser Microphones","description":"\u003cp\u003eThe sE Electronics sE4400(P) is a factory-matched pair of large-diaphragm condenser microphones built for stereo recording and flexible single-microphone applications. Each microphone uses a hand-crafted true condenser capsule and selectable pickup patterns to adapt to a broad range of sources. The pair is intended for recording engineers, musicians, project studios, and live-production users who need two closely matched microphones for consistent stereo capture.\u003c\/p\u003e\u003cp\u003eIts smooth, natural character is suited to lead vocals, acoustic instruments, piano, brass, electric guitar cabinets, drum overheads, orchestral sources, and room capture. Four selectable polar patterns let the microphones move from focused source isolation to wider ambient or stereo recording techniques. This makes the pair practical for sessions where the microphone position and pattern need to change with the source.\u003c\/p\u003e\u003cp\u003eEach sE4400 uses a hand-crafted 1-inch, gold-sputtered true condenser capsule with dual diaphragms. The microphones are tested, tuned, and sonically matched in-house for closely aligned frequency response between the two channels. That matching helps support balanced stereo imaging when the microphones are used on a stereo bar or as a spaced pair.\u003c\/p\u003e\u003cp\u003eSwitchable low-cut filters at 40 Hz and 80 Hz help reduce low-frequency rumble, footfall noise, and excess proximity effect. Selectable -10 dB and -20 dB attenuation pads allow the microphones to accommodate louder sources such as drums, brass, and guitar cabinets. With up to 157 dB SPL handling when the -20 dB pad is engaged, the sE4400 can cover both detailed and high-level recording work.\u003c\/p\u003e\u003cp\u003eThe matched-pair package provides the core hardware needed to begin stereo microphone placement, including two custom shockmounts, thread adapters, a stereo mounting bar, and a metal case. It connects through standard 3-pin XLR and requires 48V phantom power from a compatible audio interface, microphone preamp, mixer, or recorder. It is a useful upgrade for studios adding a versatile multi-pattern pair for overheads, instruments, ambience, and stereo recording setups.\u003c\/p\u003e\u003ch3\u003eKey Features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFactory-Matched Pair:\u003c\/strong\u003e Two microphones are tested and tuned for closely matched frequency response.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour Polar Patterns:\u003c\/strong\u003e Choose cardioid, hypercardioid, omnidirectional, or figure-8 for the source and room.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e1-Inch True Condenser Capsule:\u003c\/strong\u003e Gold-sputtered dual-diaphragm design supports detailed, natural capture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSwitchable Low-Cut Filters:\u003c\/strong\u003e 40 Hz and 80 Hz filters help manage rumble and proximity effect.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable Attenuation Pads:\u003c\/strong\u003e -10 dB and -20 dB pads accommodate high-SPL instruments and amplifiers.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eStereo Recording Accessories:\u003c\/strong\u003e Includes two shockmounts, a stereo bar, thread adapters, and metal case.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eDesign \u0026amp; Installation\u003c\/h3\u003e\u003cp\u003eThe sE4400 uses a die-cast all-metal housing, all-metal switches, and a rugged spring-steel wire-mesh grille. Its flat, round-edged chassis is designed to work with the included custom suspension shockmount. The matched-pair set stores and transports in its included metal case.\u003c\/p\u003e\u003cp\u003eConnect each microphone to a balanced XLR microphone input and enable 48V phantom power only on compatible equipment. Use the included stereo mounting bar for coincident or near-coincident stereo techniques, or place the microphones separately for spaced-pair recording. Select the polar pattern, low-cut filter, and pad for the source, level, room sound, and desired rejection of surrounding sound.\u003c\/p\u003e","brand":"sE Electronics","offers":[{"title":"Default Title","offer_id":45669443043398,"sku":"sE4400(P)","price":840.51,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0048\/4163\/5910\/files\/81eOuAnozML.jpg?v=1784503753"}],"url":"https:\/\/audiowatt.store\/collections\/condenser-microphones.oembed","provider":"Audio Watt Store","version":"1.0","type":"link"}